Product And Package Contents; Preliminary Warning Notices; Initial Operations, Safety Instructions; Working On The Device - Laserworld CS-1000RGB Bedienungsanleitung

1.

Product and package contents

Please check if all listed parts are included and undamaged. Included in delivery:
Laser system, power cable, keys, interlock bridge plug, manual
2.

Preliminary warning notices

• Please use this device only according to these operating instructions.
• Do not use the device if there are any visible damages on housing, connector panels, power
supplies or power cords.
• Never look directly into the light source of a laser projector. Danger of damage to the eyes
or even blindness in extreme circumstances!
• This device must not be permanently connected to mains. Disconnect it from mains or use
the power button to switch if off if not in use.
• Do not operate the device at high humidity, in the rain or in dusty environments.
• Protect device against dripping or splashing water. Do not place any liquid filled containers near
to this device.
• Any warranty claims are void if the warranty label is removed or tampered with in any
way.
3.

Initial operations, safety instructions

• Make sure to use correct voltage; see information on device & in this manual.
Make sure that the device is not connected to mains during installation.
•
• Installation has to be done by technical experienced and qualified persons according to
safety regulations of the respective country.
• Always ensure that maximum permissible exposure (MPE) is not exceeded in areas ac-
cessible to the public or members of staff.
• In some countries an additional inspection by technical control institutes could be necessary.
• Connect an easily accessible interlock connector or circuit breaker to the projector.
• The power supply should be easily accessible.
• When installing the laser mount it with a minimum distance of 15 cm from walls and objects.
• For safe setup e.g. on walls or ceilings please use a safety cord. The safety cord should be able
to withstand tenfold the weight of the device. Please follow the accident prevention regulations of
professional associations and/or comparable regulations for accident prevention.
• If the device has been exposed to great temperature changes, do not switch it on immediately.
Condensation (or any moisture / water formed) may damage device.
• Never use dimmer, RC or other electronically switched sockets. Whenever possible, do not
use the laser projector together with large appliances (especially fog machines) on the same
mains!
4 / 45
Laserworld CS-1000RGB MK3 Laserworld CS-1000RGB MK3
• Ensure sufficient ventilation and do not place the device on any warm or heat radiating sur-
face. Especially the ventilation openings must not be covered!
• Ensure that device does not get overheated. Make sure that the device is not exposed to
spotlights (especially moving heads). Heat of spotlights could overheat laser in a little while and
leads to a degradation of performance.
• This unit is intended for indoor use only.
4.

Working on the device

• This product has no user serviceable parts inside and should only be main-
tained and serviced by a qualified engineer.
• Be sure that the mains plug is not connected to the power supply while
installing.
• Take off all reflecting things like rings, watches etc. before starting to
work with or at the projector.
• Only use non-reflecting tools to work on device.
• Wear protective clothing (like glasses, gloves etc.) according to laser
power and wavelength of the laser.
5.

Service notes

• Moisture and heat can reduce lifetime of the laser system dramatically and expires any warranty
claim.
• Quick on/off switching of this device will reduce durability of the laser diode dramatically.
• Avoid sharp knocks and shocks to this device and ensure sufficient protection during transporta-
tion. Look after your Laserworld product.
• To increase durability of your laser, protect device against overheating:
• Always ensure sufficient ventilation.
• Do not face spotlights (especially moving heads) to the device.
• Check temperature after approx. 30 minutes with each new installation. If necessary install the
projector at a place with different temperature.
• Keep the device dry. Protect it from moisture, rain and damp.
• Switch off device when it is not needed. Diodes are switched on and can wear out even if there
is no visible laser output.
• Please ensure the fans and heatsinks are clear from dust and debris otherwise the risk of over-
heating may occur. If the unit and airways appear to be blocked then please contact a qualified
service engineer to maintain and service the product.
• The devices of the Club Series are not meant for professional applications. They are not suitable
for 24/7 operation.
• Always place the laser behind fog machines and hazers
• Avoid direct exposure of the laser to moisture
5 / 45