Customer Service; Safety Advice; Before Assembly - Palram Mythos Gebrauchsanweisung

- -
-.1
-
- -
'
"
'
Customer Service
For assistance
with assembly or for replacement parts
-
please log
onto our website
or
call
our service line (number
is
on
the title
page).
Additional information
can be
found
at
our website: www.palramapplications.com
Safety Advice
It
is
of utmost importance
to assemble
all
of the
parts
according to the directions.
Do
not
skip any step.
We strongly recommend using
work
gloves during assembly.
Always wear shoes and safety goggles when working with extruded aluminium.
If using
a
step ladder or power tools ensure that you follow the manufacturer's
safety advice.
Do not touch overhead power cables
with the aluminium
profiles.
Do
not attempt to assemble the greenhouse
in
windy or wet conditions.
Dispose
of
all
plastic bags safely keep them out of reach
of
small children.
Keep
children away from the assembly
area.
Do not lean against or push
the greenhouse during construction.
Do
not position your greenhouse
in an area
exposed to excessive wind.
Do
not attempt to assemble this greenhouse if you
are
tired, have taken drugs or
alcohol or if you
are
prone to dizzy
spell.
Hot items such
as
recently used grills,
blowtorches
etc. must
not
be stored
in
the
greenhouse.
Ensure
there
are no
hidden pipes or cables
in
the ground before
inserting the
pegs.
This
product
is
designed to use
as
greenhouse only.
Care &
Maintenance
When your greenhouse needs to be cleaned,
use
a
mild detergent solution and rinse with
cold clean water.
DO NOT use
acetone, abrasive cleaners or other
special
detergents to
clean
the
clear panels. It
is
recommended to check periodically that
roof panels'
caps (plastic
part
329 &
profile
981) are set
in
place.
Tools
&
Equipment
Tape measure
Large hammer
Work gloves
Spanner
Lubricant T001
-
Special
tool for Screws
411
and nuts 412
Phillips head screwdriver
Step ladder
Drill
bit
Ii
30
Before
Assembly
This
is
a
multi-part assembly best
achieved by
two people. Allow
at least
half
a
day for assembly process.
Selecting
a
site
-
the greenhouse must
be
assembeld, positioned and fixed on
a
flat
level surface.
Choose
a
sunny position away from
overhanging
trees.
We are
strongly recomend to fix your
greenhouse directly to
a
solid concrete
foundation. When doing that
use
the
pre
drilled holes
in
the metal
base
supplied.
Take
out
all
components parts
of
the
packages. Sort the parts and check
against the contents parts
list.
During assembly parts should
be laid
out
close at hand. Keep
all
small parts (screws
etc.)
in
a
bowl
so
they
do
not get
lost.
In
purpose to facilitate parts' identification
and assembly process, all-positioned
profiles
are
used
in
this greenhouse.
As
a
result some apertures
in
the profiles
are
not
used during assembly.
.
-5
-
A
. -
-
. -
"
'
During Assembly
Carry out the assembly steps
in
the order
set
out
in
the instructions.
You may use Silicon
lubricant
spray
in
order to
help you slide the profiles on
the connectors.
Do not spray the Polycarbonate panels.
Use
the rubber malet
if necessary.
Step
1: Make sure
the
base
is
square by
measuring the diagonals and
level by using
a
spirit
level.
Step 5:
Part
A994, A995
are in
the back of the
greenhouse. Fixing them determines the front
side of the greenhouse.
Steps 8, 10, 15:
The oval hole
in
the crossbars
A256 should always be assembled to the
base
of the greenhouse.
Door assembly (Steps 9, 56-62)
Door
can be installed as
a
left hand door or right
hand door to your decision.These instructions
show
a
right hand door
assembly.
Step 9: determines door direction door post
987
is
where door hinges will be located.
Steps 56-62: Door assembly should
be
done
according to this decision.
Step 42: Decide on the window's location
before assembly.
Window
can be installed
in
one of the indicated options.
Step 55
:
In
case
the window
is
not closed
properly, please release
the
screws, adjust the
profile and
tighten the
screw.
Step 68:
Firmly
connect the greenhouse to
a
level
final position immediately after completion
of the
assembly.
Tighten
all
screws when completing assembly.
Ile
. -
OS
"
"'
-
5-
.
Ile
-
-
-9
-
-
--le-.