Customer Service; Safety Advice; Before Assembly - Palram Harmony Montageanleitung

IMPORTANT
Please read
these instructions carefully before you start to assemble this greenhouse.
Keep
these instructions
in
a
safe
place for future
reference.
Customer Service
For assistance
with assembly or for replacement parts
-
please log
onto our website
or call
our service line (number
is
on
the title
page).
Additional information
can be
found
at
our website: www.palramapplications.com
Safety Advice
It
is
of utmost importance to assemble
all
of the parts according to the directions.
Do
not
skip any step.
We strongly recommend using work gloves during assembly.
Always wear shoes and safety
goggles when working with extruded aluminium.
If using
a
step ladder or
power tools
ensure
that
you
follow the manufacturer's
safety advice.
Do
not touch overhead power
cables
with the aluminium
profiles.
Do
not attempt to assemble the greenhouse
in
windy
or
wet conditions.
Dispose
of
all
plastic bags safely keep them out of reach of small children.
Keep
children away from the assembly
area.
Do
not
lean
against or push the greenhouse during construction.
Do
not position your greenhouse
in an area
exposed to excessive wind.
Do
not attempt to
assemble this greenhouse if you
are
tired, have taken drugs or alcohol
or if you are
prone to dizzy
spell.
Hot items
such
as
recently
used grills,
blowtorches
etc.
must not be stored
in
the
greenhouse. Ensure there
are
no hidden pipes or cables
in
the ground before
inserting the
pegs.
This
product
is
designed to
use
as
greenhouse
only.
Care &
Maintenance
When your greenhouse needs to be cleaned,
use
a
mild detergent solution and rinse with
cold clean water. DO NOT use acetone, abrasive cleaners or
other
special
detergents to
clean
the
clear panels. It
is
recommended to check periodically that
roof panels caps (plastic part 329
&
profile
981) are set in
place.
Tools &
Equipment
Tape
measure
Work gloves
Lubricant
Phillips head screwdriver
Step ladder
Drill
bit
Large hammer
Spanner
T001
-
Special
tool for
Screws 411 and nuts 412
Before Assembly
This
is a
multi-part
assembly best achieved
by two people. Allow
at least
half
a
day for
assembly process.
Selecting
a
site
-
the greenhouse must
be
,
positioned
and fixed on
a
flat
level
surface.
Choose
a
sunny position away from
overhanging
trees.
We are
strongly recomend to fix your
greenhouse directly to
a
solid concrete
foundation. When doing that
use
the
pre
drilled holes
in
the metal base supplied.
Take
out
all
components
parts of the
packages. Sort
the parts and check against
the contents parts
list.
During assembly parts should
be laid
out
close at hand. Keep
all
small parts (screws
etc.) in
a
bowl
so
they do not get
lost.
In
purpose to facilitate parts' identification
and assembly process,
all-positioned
profiles
are
used
in
this greenhouse.
As
a
result some apertures
in
the profiles
are
not
used
during
assembly.
41r°
4104
1111k
F
1OP:
.
-6
-
A
.
-
-
.
- s
" "'"'
'
Ile
. -
-
A. A.
O.
During Assembly
Carry
out the
assembly steps
in
the order
set
out
in
the instructions.
You
may
use
Silicon lubricant spray
in
order to help
you slide the profiles on the connectors.
Do not spray the Polycarbonate panels.
Use
the rubber malet if
necessary.
Step
1: Make sure
the
base
is
square by
measuring
the diagonals and
level
by using
a
spirit
level.
Step 4:
Part A994, A995 are
in
the back of the
greenhouse. Fixing them determines the front
side
of the greenhouse.
Steps
7,10:
The oval hole
in
the
crossbars A256
should always be assembled to the
base
of the
greenhouse.
Door assembly (Steps
8,
43-49)
Door
can
be installed
as a
left hand door or right
hand door to your decision. These instructions show
a
right hand door
assembly.
Step 8: determines door direction door post
987
is
where door hinges will
be
located.
Steps 43-49: Door assembly should
be
done
according to this decision.
Step 28:
Decide on
the window's location before
assembly.
Window
can be
installed
in
one of the
indicated options.
Step 42
:
In case
the
window
is
not closed
properly, please release the screws, adjust the
profile
and
tighten the
screw.
Step 51:
Firmly
connect the greenhouse to
a
level
final position immediately after completion of the
assembly.
Tighten
all
screws
when completing
assembly.
.
".
.
".
OA'
.
Ile
-
o-
-
-
--le-.
D
00'