Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Maintenance and Care
The product does not require any maintenance and should never be opened or disassembled
for any reason.
Remove connected consumer loads from the radio controlled switch socket and remove it from
the mains socket, before cleaning the product.
Only clean the product with a soft, clean, dry cloth. Never use aggressive cleaning agents or
chemical solutions since these might damage the surface of the casing or impair the operation.
Handling
• The radio-controlled switch socket is only intended to be used in dry, closed indoor
locations.
• Avoid the following unfavourable environmental conditions at the installation loca-
tion and during transportation:
- Direct sunlight
- Extreme cold or heat
- Dust or fl ammable gases, fumes or solvents
- Strong vibrations
- Strong magnetic fi elds such as those found in the vicinity of machinery or loud-
speakers
• Ensure that the insulation for the entire product is neither damaged nor destroyed.
Never disassemble the product! There are no serviceable parts inside.
• Check the product for damage before each use!
If you notice any damage, do not use the product any longer!
There is a life-threatening hazard through an electric shock!
Safe operation must be presumed to be no longer possible:
- the device is visibly damaged
- if the device no longer works
- if the device was stored under unfavourable conditions for a long period of time
- it has been subjected to considerable stress during transportation
Range
The transmission range of the radio signals, between the hand-held radio transmitter and the
radio-controlled switch socket, is up to 30 m under optimum conditions.
☞
This value, however, is the so-called "open space range" (the range the transmitter
and receiver are visible to each other, without disturbing infl uences).
In practical operation, however, there are walls, ceilings of rooms etc. between the
transmitter and the receiver, which reduce the range accordingly.
Due to the different infl uences on the radio transmission, no specifi c range can be
guaranteed.
However, trouble-free operation is usually possible in a single family house.
The range can sometimes be considerably reduced due to:
• Walls, reinforced concrete ceilings
• Coated/metallised insulated glass
• Proximity to metallic & conductive objects (e.g. heating elements)
• Proximity to human bodies
• Broadband interferences, e.g. in residential areas (DECT telephones, mobile phones, radio-
controlled headphones, radio-controlled speakers, radio-controlled weather stations, baby
phones etc.)
• Proximity to electric motors, transformers, power-supply units, computers
• Proximity to computers or other electrical devices that are improperly shielded or operated
without any cover
Disposal
Please dispose of the product when it is no longer of use according to current statu-
tory requirements.
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the fundamental requirements and the other relevant regulations of the
directive 1999/5/EC.
☞
The Declaration of Conformity for this product can be found at www.conrad.com.
Technical Data
Reception frequency .....................433 MHz
Operating voltage .........................230 V/AC, 50 Hz
Protection class ............................I
Input power ...................................2000 W Ohm resistive load, 300 W inductive load
Address codes ..............................4 (adjustable by turn switch)
Switching channels .......................4 (adjustable by turn switch)
LED ...............................................lights up, when the mains socket/consumer load is activated
Dimensions (H x W x D) ...............95 x 50 x 73 mm (incl. connection plug)
......................................................approx. 95 x 50 x 35 mm (not including connection plug)
Operating environment .................only suitable for enclosed, dry indoor locations
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
Werbung
