Werbung
These instructions explain how to correctly use this product.
You are responsible for heeding each warning and using your equipement correctly.
Any misuse of this product will create additional dangers. Contact CLiC-iT if you have any doubt or difficulty understanding
these instructions.
The selection of your system's components (lanyards, connectors, harnesses), as well as their assembly and installation, must
be done by competent persons to be suitable for the adventure park where they will be used.
1. Description
This product is a Personal Protection Equipment designed for leisure activities at heights (high rope adventure parks) as per
standard EN17109:2020.
CLiC-iT RiDER Pulley is an MCD (mobile connection device) designed to prevent risk of fall from height, and operate along an
CLiC-iT RiDER safetyline regarding the recommendation of the PPE 2016/425. Its main functions are to assure the user to the
lifeline and to provide a continuous movement through it.
This product must not be pushed beyond its limits, nor be used for any purpose other than that for which it is designed.
This PPE is controled by APAVE SUD EUROPE CS 60193 - 13322, MARSEILLE CEDEX 16, France. CE number 0082.
Unique model.
Equipement identification: CLiC-iT reference: DAS436
Symbols used. Inform you of:
Πproduct specific manual consultation
some potential dangers related to the use of the product
Ž visual checks
control points
(1) Safety line cable: This product is designed to be used exclusively on Ø12mm lifelines, made of galvanized steel cable, type
7x19, steel core, compacted. Do not use any other type of cable. This product must not be used on other type of safety line.
Related documents. (1) PPE Checking, (2) Manuals in other languages, (3) UE conformity check.
WARNING
Activities involving the use of this equipment are inherently dangerous. You are responsible for your own actions, decisions
and safety. Failure to heed any of these warnings may result in severe injury or death.
This product must only be used by competent and responsible persons, or those placed under the direct and visual control of
a competent and responsible person. You are responsible for your actions, your decisions and your safety and you assume the
consequences of same. If you are not able, or not in a position to assume this responsibility, or if you do not fully understand
the Instructions for Use, do not use this equipement.
2. Components
A. Movement system B. Locking system C. Carabiner housing
3. Compatibility
3.1 Carabiner.
Use this product in conjunction with a Pin Lock type carabiner to guarantee a category E equipment (device that
is permanently attached during operation and can only be opened with a tool).
Read carefully the user manual of the carabiner.
3.2 Lanyard.
EN12277+A1 harness are recommended. EN17109 lanyards are recommended for connection to the harness.
The connection of the lanyard to the carabiner and the harness must not be removable (a lark´s foot connection is considered
as nonopenable). Consult your lanyard manual to connect to the carabiner and harness.
Define the lengh of the lanyard in accordance to the height of the safety line and the size of the person.
4. Installation
4.1 Procedure for opening a Pin-Lock carabiner
ŒInitially the carabiner is locked, Use a pin tool to press the carabiner button. Your carabiner can operate with a special pin,
refer to the instructions of your carabiner, ŽMake a clockwise turn on the lock cylinder of the carabiner, keeping the previous
operation, proceed with the opening of the carabiner, Once the effort is withdrawn, the carabiner automatically returns to its
locking position.
4.2 Installing the product on the safety line
ŒMake sure you are in a safe position on the floor and disconnect the carabiner from CLiC-iT RiDER Pulley in case it is connected
Before connecting the MCD to the safetyline you must have your lanyard properly connected to the harness and your carabiner
properly connected to the lanyard too (see respectives manuals) ŽUnlock the MCD by pressing with both thumbs on the bottom
of the Locking Cam (part C) - Insert the MCD on a straight portion of compatible cable. Be sure to hang the MCD with the
opening side facing the anchors of the rope course. Close the Locking Cam until it magnetically locks - Insert the carabiner
according to the orientation shown on picture ‘Adjust the length of the lanyard and move the MCD along the cable to check
the correct operation.
5. Inspection
To ensure the correct condition of the product, please refer to the control points described in the PPE Checking file. Only B, C
and D parts can be replaced, and only by the manufacturer.
5.1 Movement system inspection
Correct state of the rollers is checked by moving the product through the safety line cable.
EN
Sheaves have a high service life, just need a visual inspection.
In case the movement is not correct, sheaves must be replaced.
Please contact the Technical Service to request a replacement of part D.
5.2 Locking system inspection
Parts B and C, must be inspected after a user falls or after approximate use by 1000 users. The open area of the channel where
the cable is hosted is 7,5-8mm between parallel faces of parts. B and C parts incorporate a 0.5mm depth slot to control the
wear produced with use.
Both parts should be replaced when you cannot clearly see any wear indicator.
Please contact the Technical Service to request a replacement of parts B and/or C.
6. Precautions
The list of recommendations stated here is only to be used as a general guideline to limit the risks involved with the use of the
product. This guideline is by no means exhaustive. It should be taken into consideration and validated by park builders and users.
It is the responsibility of all involved parties to minimize the inherent risks involved in the use of the product.
This list is not exhaustive with the practice of the ropes course. Take into consideration that among other risks, a neck entrap-
ment, or a trauma to the larynx are part of the risks inherent in this activity.
6.1 General usage precautions
ŒCaution with possible tangling of MCD rollers with the participant's hair. It is recommended to wear helmet and properly tie the hair
Possible trapping of the fingers or possible bums with the wire. We recommend the use of gloves ŽThe lanyard must not be
too loose or too short, so that it allows the correct passage of the product through the anchoring and allows easily movement
throw games, but does not allow fall. Properly adjust lanyard height before starting the game. Maximun height of fall must
not exceed 0.3 to 0.4m Attention. Check the cable elongation and the distance to the ground. Please check throughout the
course, according to the lengths of lanyards defined, that in the event of a fall, there is no risk of collision with the ground or
other elements of the course, in accordance with the recommendations of standard EN15567-1 Attention. Check the cable
slope and arrival speed.
6.2 Precautions on sloping safetylines, or ziplines
ŒThe maximum weight allowed for zip lines is 120kg The maximum length of zip line allowed to use the product is 150m
ŽThis device is designed and limited to use on ziplines as scope of rope courses activities
7. Traceability and marking
ŒManufacturers
Compilance with EU Regulation 2016/425
ŽNumber of the body in charge of equipment manufacturing control: APAVE SUDEUROPE SAS. CS60193- 13322 Marseille Cedex 16
France. Notified body involved in the EU type examination and in charge of equipment certification: APAVE SUDEUROPE SAS (0082)
20kN: Minimum static resistance of the product in vertical direction, guaranteed at the time of production and validated during UE check
Safety line compatibility. Diameter of the cable
‘Carefully read the notice before using the product
’Individual product identification number. SN: XXXX.MM.YY (XXXX: unique identifier number - MM: manufacturing month - YY:
manufacturing year)
“Reference of the product. CLiC-iT reference: DAS-436
”Standard EN 17109:2020
8. Further information
When to retire your equipment.
WARNING. an exceptional event can lead you to retire a product after only one use, depending on the type and intensity of usage
and the environment of usage.A product shall be discarded in a park when:
Has suffered a fall or considerable effort and its functionality is compromised
The result of the product inspections was not satisfactory
You doubt its reliability
You do not know the complete history of use
When its use is obsolete (legislative evolution, normative, technical or incompatibility with other equipment, etc.)
A.Lifetime. unlimited B.Acceptable Temperature. Use temperature between -30ºC and +50ºC C.Precautions for use. Any
contact with chemical product could alter the resistance and integrity of the product. Damp equipment, or which has frozen
up, may not operate properly D.Cleaning. Don´t clean the product with soap or water. To remove dirt from the MCD use air or a
damp cloth E.Saline - Enviroments. Avoid exposure of the product in saline environments F.Storage - Transport. After use in wet
weather, dry the product with a soft cloth, and store it in a dry and ventilated place G.Maintenance. The product does not need
to be lubricated. Consult PPE Checking file for maintenance H.Modifications - Repairs. These products must be thorouglhly
checked annually by a qualified professional with a prior written certification from SARL DEHONDT. It is forbidden to modify or
repair these products yourself without prior training and written authorisation from SARL DEHONDT.
GUARANTEE
Manufacturer offers warranty for 2 years against any material or manufacturing defect. Normal wear, early oxidation by saline
environment, modifications, incorrect storage, negligence and uses for which this product is not intended are excluded.
RESPONSABILITY
DEHONDT SARL are not liable for direct, indirect, accidental or any other consequences occurring or due to the use of its products.
DEHONDT SARL waive any responsibility if the storage, transport, use, maintenance and cleaning instructions are not met.
Werbung
