Warranty Conditions - HABYS evero V4 Bedienungsanleitung

VIII. WARRANTY CONDITIONS
1. For the purposes of the guarantee:
a) "Manufacturer" refers to HABYS Spółka z ograniczoną odpowiedzialnością (Limited Liability Company)
with its registered seat in Jasło, ul. Produkcyjna 16, 38-200 Jasło, entered into the Register of
Entrepreneurs kept by the District Court in Rzeszów, XII Commercial Division of the National Court
Register, with the assigned KRS number: 0000513317, with the share capital in the amount of PLN
10.750.000 (ten million seven hundred fifty thousand zlotys), the capital has been fully paid up, NIP:
6852208438, REGON: 180186290.
b) "Buyer" refers to the final Buyer of the equipment, manufactured by the Manufacturer, including both
the consumer and the entrepreneur.
c) "Distributor" refers to an entity that, under an agreement with the Manufacturer, sells the Equipment
in a designated area.
d) "Authorized Service Centre" refers only to a service held by the Manufacturer or a service indicated by
the Manufacturer and held by its Distributor,
e) "Equipment" refers to a movable item, manufactured by the Manufacturer, being the subject of the
sales and to which the said warranty applies.
2. The manufacturer ensures good quality and efficient operation of the equipment for which the warranty
card has been issued, for the period of: 2 years for constructional elements, 2 years for upholstered
elements and 2 years for electronic and hydraulic accessories.
3. The guarantee repair does not include the activities provided for in the manual, which the Buyer is obliged
to perform on his own (installation of the Equipment, maintenance of the Equipment, etc.).
4. Liability under the guarantee covers only defects resulting from causes inherent in the Equipment., In
particular, the guarantee does not cover any damage resulting from improper or inconsistent use, storage,
maintenance or transport of the Equipment, as well as colour differences between the parts exposed and
not exposed to solar radiation, the influence of chemical or abrasive agents, atmospheric pollution or
accidental punctures and abrasions, the presence of stains or rings from greasy or dying substances (fats,
creams, lotions or oils), permanent staining with dyes such as inks, permanent markers or other non-
permanent dyes used in the production of clothing (e.g. dyes used to make blue jeans).
5. The guarantee does not cover any mechanical damage to the Equipment.
6. The buyer loses the guarantee rights in the event of:
a) the Manufacturer states that the Equipment was repaired by entity other than the Authorized Service,
b) making any design modifications to the Equipment without the prior written consent of the
Manufacturer,
c) using the Equipment contrary to its intended use,
d) using the Equipment after revealing any defect in it.
7. Regardless of the loss of the guarantee rights, described above, in point 6, the Manufacturer shall not be
liable for any damage to property or caused to third parties, which may be caused by the use of the
Equipment covered by the guarantee.
8. The guarantee does not exclude or limit the rights resulting from the warranty for defects. Exercising the
rights under the guarantee does not affect the seller's liability under the warranty for defects. If the Buyer
exercises the rights under the guarantee, the time limit for the exercise of the rights under the warranty for
defects is suspended on the date the Manufacturer is notified of the defect. The period runs further from
the date of the Manufacturer's refusal to perform the obligations arising from the guarantee or the
ineffective expiry of the time for their performance.
9. The scope of the guarantee coverage is limited to the territory of the country in which the Equipment was
sold.
10. The Manufacturer shall perform its obligations under the guarantee (removal of defects or damage to the
structure of the Equipment arising from reasons inherent in the Equipment, and disclosed during the
guarantee period) free of charge within 14 days from the date of delivery of the Equipment to the
Manufacturer or the Authorized Service Centre. If the repair of the Equipment cannot be performed within
the above-mentioned period, the Manufacturer shall inform the Buyer of the above, and also indicate the
reasons for the delay and the expected date of fulfilment of the recognized guarantee request.
EN
15