Werbung
Verfügbare Sprachen
Verfügbare Sprachen
23874 Tablet PC holder bundle
This bundle consists of two items:
- 19744 Tablet PC stand holder »Biobased«
- 23873 Monitor mount (holder arm)
INTENDED USE
The universal 19744 tablet PC stand holder is suitable for all tablets ranging in size from approx. 10" to 16".
Highly mobile 23873 holder arm allows for the utmost in flexibility in positioning the tablet.
FEATURES and CAPABILITIES
- Tablet PC stand holder and monitor mount are simply screwed together.
-
This screw connection is distinguished by its ruggedness, speed, and flexibility (can be rotated, for example).
- Holder arm table clamp attaches to plates up to 85 mm thick.
- Tablet can be positioned almost infinitely within the pivot radius of 800 mm.
- Detailed descriptions of the 19744 tablet PC stand holder and 23873 monitor mount: see separate instructions.
Thank you for choosing this product. Please read and follow these instructions carefully. They provide information on all of the important steps necessary to set up and
operate your product safely. We recommend that you also keep them for future use.
SAFETY INSTRUCTIONS
GENERAL INFORMATION
- The possibility of adjusting the product inherently involves pinch hazards. This means careful and attentive handling during installation, use, and maintenance is crucial.
- The product must be protected from adverse external influences such as: moisture, wind, impacts (e.g., by the audience)
- Good care and handling will maintain your product's functionality and durability and help to ensure the safety of persons and products most of all.
- If your product is damaged, you should stop using it and replace or repair any defective or damaged parts before use.
OPERATION
- The tabletop must be suitable to hold the product. This means:
-
a. The tabletop must be flat and parallel and not more than 85 mm thick.
-
b. It must be possible to push the clamp into place over the entire area and until contact is made. This corresponds to an area 150 mm wide and 110 mm deep.
-
c. The plate or table must be able to bear the load on a long-term basis.
- Be sure the monitor mount is properly attached to the tabletop.
- The extension arm (23873-c) must not extend past the pole (23873-a).
- The pneumatic mechanism of the 23873 holder arm can and should be adjusted to the tablet's weight. DieThis prevents the load from declining unintentionally later on.
- The 19744 tablet PC stand holder must be properly screwed onto the threading of the 23873 monitor mount. We recommend approximately 3 revolutions.
- Please attach the tablet in the holder carefully as described in the instructions for 19744 and ensure that it is securely in place.
- The 23873 monitor mount should also be installed and handled according to the information in the instructions.
- Handle the entire installation carefully; especially if there are any changes in settings (angle, format, and alignment), care must be taken to ensure that the tablet holds
-
securely.
SET-UP INSTRUCTIONS
This 23874 tablet PC holder bundle combines the products 19744 and 23873, each of which is described in detail in separate instructions = (> sep. inst.) These overall
instructions refer to the separate instructions at various points.
1. COMPONENTS / SCOPE OF DELIVERY
Please perform a visual inspection to determine whether all parts are
present and, as far as can be seen, are in good order.
19744 TABLET PC STAND HOLDER (> sep. inst.)
a Pivot joint with 3/8" internal threading
b Holder (base, slider, clamp)
c Angle bracket (with felt and rubber cap)
23873 MONITOR MOUNT (> sep. inst.)
a Clamp with pole, diameter 32 mm
b Spring arm with monitor mount plate (> sep. inst.),
b
replaced here by:
b.1 Spring arm with 3/8" bolt thread (see Fig. b.1)
c Extension arm
23873 SMALL PARTS in transparent pouch (A-D), contents:
A Phillips screws M4 x 12/30 mm (4x each) – not required here;
A
can be used optionally in conjunction with VESA plate (> sep. inst. 2)
B Allen wrench SW3 + SW5
C Plastic bushing diameter 12 x 16 mm (4x) – not required here:
C
can be used optionally in conjunction with VESA plate (> sep. inst. 2)
C Cable clip for pole, diameter 32 mm (> sep. inst. 7)
D Threaded bolt M6 x 25 mm (> sep. inst. 4, 5)
D Cover (> sep. inst. 4)
23873 ACCESSORIES, optional: VESA plate for monitor
23873 ACCESSORIES,
see (> sep. inst. 4, 5, 6)
23873 ACCESSORIES,
- enclosed loose here
2. PREPARATION
2.1 Assemble 19744 (> sep. inst.)
2.2 Attach 23873 (> sep. inst.)
3. Screw 19744 and 23873 together
3.1 Make sure the 3/8" internal thread is screwed
3.1
zinto the joint until contact is made.
3.2 Now place the internal thread of the 19744 on the
3.2
bolt thread of the 23983...
3.3 ...and screw into place for approximately 3 revolutions
3.3
(until the tablet PC holder is aligned vertically).
3.4 Now turn the knurled screw at the base of the
3.4
threaded bolt until...
3.5 ...the holder arm and joint are screwed tightly together.
Werbung
