Home Screen; Live Tv Mode Menu Content; Channels; Tv Options - Horizon 7 Serie Nutzerhandbuch

If the Satellite option is selected, the Antenna Type
screen will be displayed next. If you have a Direct
satellite system, you can proceed to the next step
quickly by selecting the Next option here. Highlight
More and press OK to set the antenna type manually.
Single, Tone Burst, DiSEqC, and Unicable options
are available. Highlight the antenna type that
corresponds to your satellite system and press OK or
the Right directional button to proceed to the next step.
Next screen will be the Select Operator screen. You
can select only one operator from the list. Highlight
the desired operator and press OK or the Right
directional button to proceed. Some of the options in
the following steps may be preset and/or additional
steps may be added or some steps may be skipped
depending on the selected operator in this step. Check
the parameters in each step before proceeding and
adjust if necessary. You can highlight General and
press OK or Right directional button to proceed with
normal satellite installation.
LNB List screen will be displayed next. You may be
selected country, antenna type and operator in the
previous steps. Highlight the desired satellite option
and press OK or the Right directional button to set
the parameters. The Satellite Status of the first
satellite option will be set as On. In order to enable
channel scan on the satellite, this option should be
set as On
Following satellite parameters will be available. You
may not be able to change all settings depending on
the previous selections.
Satellite Status: Set the status option to On to
enable channel search on the selected satellite.
Highlight this option and press OK to change the
status.
Satellite Selection: Select the satellite on which you
want to perform a channel search.
Scan Mode: Set your scan mode preference. Full
and Network options will be available. If you are
going to perform a network scan, make sure that
you have adjusted the Frequency, Symbol Rate
(Ksym/s), and Polarisation parameters under the
Transponder option accurately.
Scan Type: You can perform a scan for free or
encrypted channels only. If the Only Free Channels
option is selected encrypted channels will not be
installed. Select All to scan all channels.
Store Type: You can select to store TV channels
(referred to as 'Digital Channels' in the menu) or
radio channels only. Select All to store all channels.
Transponder: Adjust the Frequency, Symbol Rate
(Ksym/s), and Polarisation parameters for the
selected satellite if necessary.
Set the parameters for LNB.
For DiSEqC antenna type select the correct DiSEqC
port corresponding to your satellite system. Set other
parameters in accordance with your satellite system
if necessary.
Signal Quality: The signal quality status is displayed
as a percentage.
Signal Level: The signal level status is displayed
as a percentage.
Press the Back/Return button and select next satellite
changes, highlight Next on the LNB List screen and
press OK or Right directional button to proceed.
If Load Preset List option is selected in the previous
step next steps will be skipped and the preset channel
list installation will start. If the correct satellite has not
been selected for SatcoDX installation, a warning
dialogue will be displayed on the screen. The satellite/s
that can be selected will be listed. Press OK to close
the dialogue and then set the satellite accordingly.
Channel Scan screen will be displayed next. Select
Skip Scan to proceed without performing a scan and
complete the initial setup. Select Scan and press OK
or the Right directional button to start the search.
While the search continues you can press the Back/
Return button, highlight Skip Scan and press OK
or Right directional button to stop the search. The
channels that have already been found will be stored
in the channel list.
When the initial setup is completed a message will be
displayed. Press OK
You will be asked to give your consent to the
collection of your data. Read the text on the screen
for detailed information. Highlight Accept and press
OK to give your consent and proceed. To skip
without giving your consent, select Next. You can
change this setting later using the Settings>Device
Preferences>Manufacturer Usage & Diagnostics
menu.
Home Screen will be displayed. You can press the Exit
button on the remote to switch to Live TV mode and
watch TV channels.

Home Screen

be connected to the Internet. Connect the TV to a
home network with a high-speed Internet connection.
You can connect your TV wirelessly or wired to your
modem/router. Refer to the Network and Internet
and Connecting to the Internet sections for further
information on how to connect your TV to the Internet.
The Home menu is the centre of your TV. From the
Home menu, you can start any application, switch to a
TV channel, watch a movie, or switch to a connected
device. Press the Home button to display Home
English - 11 -
Screen. You can also select the Android TV Home
option from the Inputs menu to switch to Home
Screen. To open the Inputs menu, press the Source
button on the remote or press the Menu button on the
remote when the TV is in Live TV mode, highlight the
Source option in the TV options menu, and press
OK. Depending on your TV setup and your country
selection in the initial setup, the Home menu may
The available options of the Home Screen are posi-
tioned in rows. To navigate through the Home Screen
options use the directional buttons on the remote.
Apps, YouTube, Google Play Movies & TV, Google
Play Music and Google Play related rows and rows of
the applications you have installed might be available.
Select a row then move the focus to the desired item
in the row. Press OK button to make a selection or to
enter a sub-menu.
On the upper left of the screen, search tools will be
located. You can choose either to type a word to start
a search via the virtual keyboard or try voice search
option if your remote has a built-in microphone.
Move the focus to the desired option and press OK
to proceed.
On the upper right of the screen, Notifications,
Inputs, Network and Internet (will be named as
Connected or Disconnected according to the current
connection status), Settings and the current time will
preferences using the Date & Time menu options from
the Settings>Device Preferences menu.
First row will be the Apps row. Live TV and Multi
Media Player apps will be available alongside with
other favourite apps. If not, highlight Add app to
favourites option (plus sign) on the Apps row and
press OK. Then select the app you want to add
and press OK. Repeat this procedure for each app.
Highlight Live TV and press OK or press the Exit
button on the remote to switch to Live TV mode. If
the source was set to an option other than Antenna,
Cable, Satellite or ATV previously, press the Source
button and set one of these options to watch live TV
channels. Highlight Multi Media Player and press OK
to browse the connected USB devices and play/display
the installed media content on the TV. The audio can be
played through the speakers of the TV or through the
speaker systems connected to the TV. To browse the
Internet, you will need an internet browser application.
Make a search or launch the Google Play Store app,
For some countries, the Home Screen will be organised
into several tabs. Home, Discover and Apps tabs will
be available. You can scroll through the tabs using
the directional buttons. Each tab will have a featured
content row at the top. In the Home tab, there will be
rows for favourite apps, recent Live TV programmes
and recommendations from streaming apps. In the
Discover tab recommendations from streaming
services will be displayed. In the Apps tab, all the
apps installed on your TV will be displayed and you
can install more from Play Store using the related
option. Depending on your TV setup and your country
selection in the initial setup, the tabs on the Home

Live TV Mode Menu Content

the Menu button on the remote to see Live TV menu
options. To switch to Live TV mode you can either press
the Exit button or highlight the Live TV app from the
Apps row on the Home Screen and press OK. For
some countries, the Live TV app will be situated in the
Home tab on the Home Screen and the row with this
app will be named as Favourite Apps.

Channels

Programme Guide: Open the electronic programme
guide. Refer to the Programme Guide section for
detailed information.
Channel Export/Import: Export this TV's satellite
channel list data to a connected USB storage device,
or import a previously exported data from a connected
USB storage device to this TV. The Channel Export
and Channel Import options will be available. Connect
a USB storage device (*) to the TV, highlight the option
you want to continue with and press OK. The Channel
Export/Import option will not be available if the input
source is not set to Satellite.
(*) The USB storage device must be formatted with the FAT32
Channel: Open the Channel menu. You can use
the Channels menu options to search for broadcast
channels. Refer to the Channel section for more
information.

TV Options

Source: Display the list of input sources. Select the
desired one and press OK to switch to that source.
Picture: Open the Picture menu. Refer to Device
Preferences section for detailed information.
Sound: Open the Sound menu. Refer to Device
Preferences section for detailed information.
Power
Sleep Timer:
your TV to enter sleep mode automatically. Set as
to disable.
or on the TV to turn the screen on again. Note that
you can not turn the screen on via the Volume +/-,
English - 12 -
OK to