Hydraulikteile Aus Edelstahl, Standard-Leistungsaufnahme - Nordson Rhino SD3 Betriebsanleitung

Position P/N P/N
— 1614877
— — 1614878
1 ------ ------
2 1614836 1614836
3 1615307 1615307
4 1615322 1615322
5 ------ ------
6 1614839 1614839
7 ------ ------
8 ------ ------
9 1615773 1615773
10 ------ ------
11 1615382 1615382
12 ------ ------
13 941450 941450
14 1609301 1609301
15 ------ ------
16 — ------
17 ------ ------
18 1605675 1605675
19 105800 105800
20 1615314 1615314
21 1611299 1611299
22 1611526 1611526
23 1611309 1611309
24 1062623 1062623
25 1611301 1611301
26 1611302 1611302
27 1611303 1611303
28 1049516 1049516
29 1611305 1611305
30 ------ ------
HINWEIS A: In Wartungssatz 1611629 für Antriebsstränge enthalten.
B: In Satz 1611626 für interne Stopfbuchspackungen enthalten.
C: In Wartungssatz 1611624 für Stopfbuchspackungen für XD3 Hydraulikteile und in Wartungssatz
1613682 für ARW-Hydraulikteile enthalten.
NS: Nicht abgebildet (Not Shown)
E 2020 Nordson Corporation
Hydraulikteile aus Edelstahl,
Standard-Leistungsaufnahme
Siehe Abbildung 11.
— PUMP, Rhino, 190 cc, XD3, stainless steel, 240 V
PUMP, Rhino, 190 cc, XD3, stainless steel, CE, 240 V
S SCREW, M5 x 0.8 x 8, button head, zinc, class 12.9, per
ISO 7380
S GASKET, pump, SD3/XD3, heated
S CONNECTOR, plastic, 2‐stage, 12‐24 AWG
S CONNECTOR, plastic, 5‐stage, 12‐24 AWG
S SCREW, socket, M5 x 55, zinc plated, class 12.9, per ISO
4762
S SEAL, pump, box, SD3/XD3, heated
S SCREW, socket-head, M4 x 0.7 x 8, zinc, class 12.9, per
ISO 4762
S SCREW, socket, M3 x 0.5 x 6, zinc, class 12.9, per ISO
4762
S HEATER CARTRIDGE ASSEMBLY, 0.38 x 4.25 long, 240
V, 250 watt
S WASHER, lock, M, internal, M4, steel, zinc, per DIN 6797
S SENSOR ASSEMBLY, RTD, heated, Rhino
S SCREW, socket, M12 x 1.75 x 55, zinc, class 12.9, per
ISO 4762
S O‐RING, Viton, 2.563 x 2.750 x 0.094, 10545
S CHAMBER, solvent, Rhino, 2.75 ID, CE
S PLUG, pipe, socket, standard, ¼ NPT, zinc
S SCREW, drive, round, 4 x 0.250, zinc
S SCREW, drive, round, 0.187, zinc
S CONNECTOR, strain, relief, 0.260‐0.545, ½ NPT
S SCREW, socket cap, M3 x 12 mm, zinc
S CORDSET, pump, Rhino, SD3, heated
S ROD, plunger, 190 cc, pump, Scoreguard, stainless steel
S PISTON ASSEMBLY, 190 cc pump, standard, stainless
steel
S ROD ASSEMBLY, 190 cc stainless steel pump, hardened
S O‐RING, ‐140, Viton, 2.237 ID, 0.103 W, 90 Duro
S SPACER, shaft support, 190 cc pump, stainless steel
S PLATE, lower, check, 190 cc pump, stainless steel
S HOUSING, bottom, 190 cc pump, stainless steel
S O‐RING, 144, Viton, 2.487 ID, 0.103 W, 75+5d, black
S PLATE, shovel, follower, 190 cc pump, stainless steel
S SCREW, socket, M12 x 1.75 x 1.75 x 300, zinc, class
12.9, per ISO 4762
Rhino
Benennung
r
SD3/XD3 Hydraulikteil
Anz. Hinweis
1
1
6
1
2
2
4
1
1
1
2
2
1
4
1 A, B, C
1
2
2
2
1
2
1
1
1
1
2
1
1
1
1
1
4
P/N 7580505_07
49