Attaching/Replacing An Insert - Conrad 2522494 Bedienungsanleitung

Description of the sharpener´s control elements
1 Mains switch ("I" = on, "O" = off)
2 Grinding wheel
3 Unlock key (to be able to remove the insert)
4 Safety switch (prevents the sharpener from being
switched on without correctly attached insert)
5 Power cable
6 Slots for attaching an insert
7 Four holes to bolt down the sharpener
Description of the inserts
The three enclosed inserts are suitable for the grinding of different tools.
Insert 1:
The insert is used to grind chisels, small or wide rip-
ping chisels or the like.
The purpose of the integrated magnet is to hold the
tool firmly in place. The small plastic insert can be at-
tached from the side if the tool is very small (so that
the magnet can hold the tool tightly).
The angle of the grinding of the tool tip can be ad-
justed laterally (pay attention to the marking).
Insert 2:
The insert is used to grind knives or scissors.
The front slot is usually used for scissors, the two top
slots for knives.
Insert 3:
The insert is used to grind drill bits.
The drill bit is clamped into the small removable drill
holder.
Installation
• In order for the sharpener to have a stable stand while performing the grinding work, it is
necessary to fasten it on a suitable surface, e.g. on a stable work table (workbench) using
4 screws.
It is also possible to mount the sharpener on a sufficiently large wooden plate and then
fasten the wooden plate to the work table (workbench) using screw clamps. The sharpener
can be easily dismantled and stored if you don't need to use it.
• Position the sharpener so that the grinding disc points to the front, towards you, and then
bolt down the sharpener using 4 suitable screws.
Connection
• Switch off the sharpener, move the mains switch on the top to the "O" position (switched off).
• Connect the mains plug to an easily accessible standard mains socket. Lay the mains cable
so that it does not hinder you in your work. Protect the mains cable from sharp edges.

Attaching/replacing an insert

• Before you replace an insert, you have to switch off the sharpener. Move the mains switch
on the top to the "O" position (switched off).
Important!
Wait until the grinding wheel has come to a complete standstill.
• Press the unlock key and pull the insert upwards and remove it.
• Afterwards, attach a different insert to the sharpener. To this end, the insert is attached to
both slots on the left and right and pushed down until the hook on the unlock key engages
with the opening of the insert.
Check that the insert fits securely. You should no longer be able to pull it upwards and out.
Once the insert has been attached correctly, the safety switch will be activated. Only
then can the sharpener be operated.
If the insert is not inserted or not fully inserted, the safety switch will prevents start-
up of the grinding wheel.
Inserts that are not required can be attached to the left and right on the sharpener.
Should they disturb you during the grinding process, you may store them in a suit-
able place.
Sharpening chisels/ripping chisels
Important!
Please consult the chapter "Safety Instructions"!
• Install the respective insert correctly. For this purpose, refer to the chapter "Description of
the inserts" and "Attaching/replacing an insert".
• Position the tool (e.g. a ripping chisel) so that the magnet (2) retains the tool (3a). For small
tools, a small plastic insert (4) can be attached on the side so that the magnet is able to
retain the tool (3g).
• The angle of the blade of the tool is adjustable. Unfasten the locking knob (3), adjust the
angle as desired and refasten the locking knob (3b and 3c).
Focus on your tool while adjusting the angle.
• When you switch on the sharpener (switch position "I"), the grinding wheel will starts to
rotate. After a few seconds the device will reach the normal number of revolutions.
• The tool can be evenly sharpened over the entire width by lateral movement of the slide
(3d). The magnet in the slide ensures that the tool can be guided neatly.
Move the tool slowly in the direction of the grinding wheel to grind the respective materials
off the tip of the tool (3e). Make sure the tip of the tool is sharpened without removing too
much material (3f).
• The transparent cover (1) protects you from a large part of the metal particles/sparks. Fur-
thermore, it allows the control of the grinding process.
• If you do not wish to grind another tool, switch the sharpener off (switch position "O"). Wait
until the grinding wheel has come to a complete standstill.
Sharpening knives/scissors
Important!
Please consult the chapter "Safety Instructions"!
• Install the respective insert correctly. For this purpose, observe the chapter "Description of
the inserts" and "Attaching/replacing an insert".