Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
Sharpener
Item no. 2522494
Intended Use
The product is intended for the sharpening of drill bits, scissors, knives and chisels.
The product is suitable only for operation with the mains voltage (220 - 240 V/AC, 50 Hz).
Always observe the safety instructions and all other information included in these operating
instructions.
Any use other than that described above could lead to damage to this product and involves
the risk of short circuits, fire, electric shock, etc. No part of the product may be modified or
converted!
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Contents
• Sharpener with 3 attachable inserts
• Operating instructions
Latest operating instructions
Download the latest operating instructions using this link www.conrad.com/downloads or scan
the QR-Code shown. Follow the instructions on the website.
Explanation of the symbols
The lightning symbol indicates a health hazard, e.g. electric shock.
This symbol indicates specific risks associated with handling, function and use.
The "arrow" symbol indicates special tips and operating information.
The product is designed according to Protection Class II.
Observe the operating instructions!
Safety Instructions
The warranty will be voided in the event of damage caused by failure
to observe these operating instructions! We do not assume liability
for any resulting damage!
We do not assume any liability for material and personal damage
caused by improper use or non-compliance with the safety instruc-
tions! In such cases, the warranty will be null and void.
• For safety and approval reasons, the unauthorised conversion and/or modifica-
tion of the product is not permitted. Never dismantle the product.
• This product is not a toy. Devices operated using mains voltages should not be
used by children. Therefore, be especially careful when children are around.
• Use the product where it is out of reach of children. The same applies to storage.
• The product is only intended for use in dry, enclosed spaces, it must not get
damp or wet.
• The design of the product complies with Safety class II.
• The mains socket into which the mains plug is plugged must be easily accessible.
• Do not pull the power plug from the mains socket by pulling on the cable.
• Do not use this product in rooms that are under adverse environmental condi-
tions, where combustible gases, vapours or dust are or may be present! There
is a risk of explosion!
• Operate the product only when it is firmly mounted with 4 screws. For safety
reasons, the operation of the product without fixed installation is not permitted.
• Keep your workstation clean.
• Only work with sufficient lighting at your workstation.
• Ensure proper ventilation during the grinding process.
• Wear suitable protective clothing, protective gloves and protective goggles when
grinding. During the grinding process hot and glowing metal particles are formed
which may lead to severe burns or eye injuries.
• The hot and glowing metal particles created in the grinding process may cause
damage to surfaces located near the sharpener (e.g. table, wall, floor, furniture).
• Therefore, never mount or operate the sharpening device close to premium-qual-
ity surfaces, furniture or floors, or use suitable underlays and protective equip-
ment. We recommend that you use the sharpener in in an appropriate hobby
room or in a garage, for example.
• Do not use the device in close proximity to easily inflammable objects either
(such as carpets, curtains) or liquids (petrol, oil).
• When working with the sharpener, do not touch the rotating grinding disc.
• Never operate the sharpener without attached insert and/or with locked safety
switch.
• Operating time must not exceed 20 minutes. Afterwards, allow the product to cool
down for at least 20 minutes before using it again.
• If the power cord is damaged, do not touch it; electric shock carries a risk of
danger to life!
• First, turn off the mains voltage to all poles of the mains socket to which the prod-
uct is connected (e.g. switch off at the corresponding circuit breaker or remove
the safety fuse, then turn off at the ELCB).
• Then you can remove the mains plug from the mains socket. Discontinue use of
the product, take it to a specialised workshop or dispose of in an environmentally
friendly manner.
• Any maintenance or repair work may only be performed by an expert.
• Never use the product immediately after moving it from a cold room into a warm
one. The condensation that forms might damage the product under certain cir-
cumstances. Furthermore, this could cause a lethal electric shock!
• Allow the product to reach room temperature before connecting it to the power
supply and putting it to use. This may take several hours.
• Avoid the following adverse conditions at the installation location and during
transport:
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impact or blows
- Strong magnetic fields such as those found in the vicinity of machinery or
loudspeakers.
• Disconnect the power supply from the power socket if the product will not be used
for a while (e.g. storage).
• When setting up the product, make sure that the cable is neither kinked nor
pinched.
• Handle the product with care; it can be damaged by impact, blows, or accidental
falls, even from a low height.
• If it can be assumed that safe operation is no longer possible, the device
must be turned off and precautions must be taken to ensure that it is not
used unintentionally. After this, arrange for an expert to check the product.
Safe operation can no longer be assumed if:
- the device is visibly damaged,
- the device no longer works
- the device has been stored under adverse conditions for a long time
- it was exposed to heavy loads during transport
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Facilities are
to be observed.
• If you have any questions that are not answered in this manual, please contact
our technical service or other specialist.
Werbung
