Profile PLI-143 Bedienungsanleitung Seite 5

PLI-143 LAMP WITH ENERGY-SAVING LIGHT 23W
PLI-149 LAMP WITH 2 ENERGY-SAVING LIGHTS 23W
We thank you for the purchase of this Profile product.
Note: It is important that you read this manual carefully
before using the product and be sure to save this
manual for possible use later.
Note
Check if building regulations apply to your area
whereby you must have the lamp installed by an
accredited electrician. An electrician can give you
information about correct wiring. Never install the fitting
outside in rainy weather.
SWITCH OFF THE POWER BEFORE YOU INSTALL
THE LAMP.
Correct installation
 With installation outside preferably choose a place
under a roof. Pay attention to the recommandations
in fig. 2
 Connect the lamp to a circuit with wall switch.
 Unscrew the stainless steel bolts (fig 1.1) on the side
to take the holder (fig 1.3) from the fitting.
 Fix the holder to the wall with 2 screws. (fig 1.2)
 Fix the lamp back on the assembled holder and
adjust the light direction as you prefer.
 Remove the cover of the cable connection (fig 3.4).
 Untie the nut (fig 3.5) and the additional attachment
(fig 3.6) and pull the power supply wires through the
opening with the rubber packing. (fig 3.7)
 The lamp must be connected to mains voltage of
230V, max. fusing 16A.
 Connect the wires according to figure 4.
 Fix the cable connection cover, the nut and the
additional attachment.
 Remove the protection glass in front (gif 3.8) and
insert the included bulb. Then fix the glass again.
 Always respect the instructions on the identification
label of the connected power cables.
 Other uses than described above can cause damage
to the product and increase the risk of short-circuit,
fire, electric shocks, etc.
 The product may not be adapted as a whole. The
safety instructions must be strictly observed.
Safety instructions
 The importer accepts no responsibility for damage
claims with respect to objects or persons that result
from incorrect use or non-compliance with the safety
instructions. Any damage claims in such cases will
be declared null and void.
 When replacing the energy-saving bulb:
the power supply must be switched
o
off.
Do not exceed the maximum wattage
o
of 32W.
Let the floodlight cool down
o
 Always replace cracked or broken glass by glass
with the same properties as the original glass.
Technical information
 Working voltage: 220-240V~50Hz
 Maximum lamp power:
PLI-143: 23W.
o
PLI145: 2x23W
o
 Maximum current strength: 10/16A.
 Dustproof and splashproof: IP44.
Maintenance
 Only use a dry, soft cloth for cleaning the lamp. And
make sure that the lamp has first cooled.
 Never immerse the lamp in water.
 Maintenance and repairs may only be carried out by
technicians who are familiar with any applicable
regulations.
Guarantee conditions
The guarantee period for PLI-143 / PLI-149
to 2 years and commences on the date of purchase.
During the guarantee period ELTRA nv will repair any
defects attributable to material or production faults.
ELTRA NV may choose to either repair or replace a
defective appliance.
ELTRA NV is not obliged to repair or replace
appliances if they have become defective as a result of
damage, inappropriate use, or modifications or
adaptations made after the purchase date.
Take any defective appliance together with the original
receipt back to the shop where the appliance was sold.
Always add a note with a description of the problem.
Damage
ELTRA NV can under no circumstances whatsoever
be held responsible for damage of whatever nature if
the appliance was not correctly installed according to
the specified installation instructions, nor for damage
as a result of unforeseen circumstances such as
natural disasters, lightening strike, etc. All such
resulting costs are consequently at the expense of the
buyer and are not covered by the guarantee
conditions.
www.profile.eu
Eltra nv, Pachtgoedstraat 2, 9140 Temse, BELGIUM
Eltra DIYeuronet, Frontstraat 14, 5405 AM Uden,
THE NETHERLANDS
UK - 1
amounts