Setting Mode; Fitting The Cuff - Hyundai HHA282104 Bedienungsanleitung

b) Insert 4 AA powerful batteries into the compartment nd ensure each
battery is in the proper direction.
Low battery and replacement
When power on, the low battery symbol
start to work, and you must replace with new batteries, otherwise the
unit can' t work.
Battery type and replacement
Please use 4pcs AA identical 1. 5V alkaline batteries.
Do not use the batteries beyond their expiry date. Please remove the
batteries if you do not need to use for long time.
WARNING:
Dispose of the battery in accordance with all federal, state and local
laws. To avoid fire and explosion hazard, do not burn or incinerate the
battery.

SETTING MODE

Note:
• When use AC adapter, the power of battery won't be consumed.
• When suddenly stop during measurement ( like the plug off from the
outlet by carelessness) , it must be reinserted the plug into the unit.
and restart the measurement.
How to set
1. Start to year:
Press button when power on , the year will be flashing, and then use
button to set year which you want, press button when you confirm the
year, then It will enter into the month and date setting mode
2. Month and date setting
Continue to above step, the screen will display MONTH-DAY and
XX-xx, and keep flashing on month , the digit will increase 1 when
press button @ each time, you could choose from 1 to 12. Press
button when you confirm the month, then it will set the date. Same as
the month setting , each time you press button @ , the digit will keep
changing from 01 to 31. Press button@ when you confirm the date,
then it will enter into the lime setting mode.
3. Time setting:
Continue to above step, the screen will display TIME and XX: XX, and
keep flashing on the digits of hour, the digit will increase 1 when press
button @ each time, you could choose from o to 23. Press button when
you confirm the hour, then the digits of minute start to flash , same
as the hour setting , each lime you press button @ the digits will keep
changing from 00 to 59. Press button when you confirm the minute,
then the total setting mode is completed.
4. Unit setting:
Continue to above step, The unit will be changed when press button@
each lime. Press button <!) when you confirm the unit, then it will enter
into the user setting mode.
will display once the unit
PROPER USE OF THE UNIT
• Please keep quiet for 5-10 minutes, and avoid eating, drinking
alcohol, smoking, exercising and bathing before taking measurement.
All these factors will influence the measurement result.
• Remove any garment that fits closely to your upper arm.
• Always measure on the same arm(normally left).
• Take measurement regularly at the same lime of every day,as blood
pressure changes even during the day.
Common factors of wrong measurement
• All efforts by the patient to support their arm can increase blood
pressure.
• Make sure you are in a comfortable,relax position and do not activate
any of the muscles in the measurement arm during measurement.Use
a cushion for support if necessary.
• If the arm artery lies lower or higher than the heart,a false reading will
be obtained.
Note:
• Only use clinically approved cuffs!
• A loose cuff or a exposed bladder causes false reading.
• With repealed measurements ,blood accumulates in the arm which
can lead to false reading.
Consecutive blood pressure measurements should be repealed after
1 minute pause or after the arm has been held up in order to allow
the accumulated blood to flow away.

FITTING THE CUFF

1) Put the cuff on a table flatly with the velcro
side down. Pass the end of the cuff through the metal loop so that
a circle is formed. The velcro closer will now be facing outwards
(ignore this step if the cuff has already been prepared) .
2) Push the cuff over the left upper arm so that
the tube points in the direction of the lower arm.
3) Wrap the cuff on the arm as illustrated. Make certain that the lower
edge of the cuff lies approximately 2 to 3 cm above the elbow and
the rubber tube leaves the cuff on the inner side of the arm.
4) Tighten the free end of the cuff and close the cuff by affixing the
velcro.
5). The cuff should be snug on your upper arm so That you can fit 2
fingers between the cuff and your upper arm. Any piece of clothing
restricts the arm which must be taken off.
6). Secure the cuff with the velcro closer in such a way that it lies
comfortably and not too tight. Lay your arm on a table (palm
upwards) so that the cuff is at the same height as the heart. Do not
bend the tube.
Note:
If it is not possible to Iii the cuff to your left arm. it can also be placed
on the right. However. all measurements should be made using the
same arm.