Heissner F636-PXC Gebrauchsanleitung & Garantie Seite 12

1 EN
Check the position and presence of the filter sponge before each use.
�
Do not point the suction hose at people or body parts.
�
Description and assembly
A Motor head
B On/Off Switch
C Drain hose
D Dirt bag
F Cap
G Locking clip motor head
H Connection nozzle suction hose
Before each use, mount the filter sponge R over the float cage to prevent water or dust from
entering the engine head A. Check the presence of the filter sponge before each reuse. Replace
any defective filter sponge immediately. Allow the filter sponge to dry before using again.
Batteries and charger are not included and are sold separately. Two batteries from the "Power X-
Change" family with the same capacity are required to operate this device. The best results in terms of
endurance and suction power can always be achieved when batteries with the same capacity from 3.0
Ah and larger are used.
Only use batteries with the same level, never combine full and half-full batteries. Always charge both bat-
teries at the same time. The battery with a weaker state of charge determines the runtime of the device.
Both batteries must always be fully charged before operation. Close the battery cover by closing the lid
and make sure it clicks into place.
Pull out the battery before all maintenance and cleaning.
Charge batteries only in chargers recommended by the manufacturer. In battery-powered devices, always
use only the batteries provided for this purpose.
Keep unused batteries away from paper clips, coins, keys, nails, screws, or other small metal objects that
could cause contacts to bypass. Store unused batteries cool (preferably 15°C) and at least 40% charged
to counteract deep discharge.
Mounting the battery: Fold up the battery cover. Then plug the two batteries into the recordings.
Manual operation (Fig. B Switch position I): Device switches on immediately. It can be vacuumed until, for
example, in wet operation the tank is full. The filling time of the tank depends on the respective operating
conditions and can vary over time. When the tank is full, a float switch in the engine head stops the suction.
At the same time, the running noise of the engine changes due to the bypass operation that has now oc-
curred. To empty, the device must now be switched off. Emptying must be done manually by pouring out
the tank. When drain hose C is mounted, the container empties automatically due to the dynamic pressure
in the tank. Make sure that the tank is completely emptied before putting the device back into operation.
Use as pond sludge vacuum cleaner / pool vacuum cleaner
Keep the device at a sufficient safe distance from the pond or pool and convince yourself of the firm
�
stand of the device.
Mount plastic pipes M of the desired length with the suction nozzle O to the handle of the suction
�
hose Q and plug the suction hose L into the nozzle H of tank I.
Mount the drain hose C on the lower connection nozzle of tank I, so that it has a slope towards the
�
end so that the tank can empty completely.
Do not operate a wet device or use the vacuum cleaner when it rains at the pond or pool.
�
Automatic mode (Fig. B Switch position II): For safety reasons and in order to be able to take the
�
correct suction position, the device only switches on with a time delay of up to 10 seconds in
automatic mode. After automatically switching on, the device then sucks in for a specified time and also
switches off automatically after a specified time for emptying. This work cycle is then repeated until the
device is switched off by means of switch B. The intake and emptying times are fixed via an automatic
program in the engine head and cannot be changed. Program times in automatic mode: switch-on
delay approx. 10 seconds, suction time approx. 30 seconds, emptying time approx. 30 seconds,
suction time approx. 30 seconds, emptying time approx . 30 seconds.... The times are independ-
ent of the filling or emptying state of the container which is subject to the respective conditions
of use and cannot be changed. Never operate the device unattended in automatic mode.
12
F636-PXC Anleitung.indd 12 F636-PXC Anleitung.indd 12
I Container
L Suction hose
M Intake manifolds 4 pieces
O Suction nozzle
Q Grip
R Filter sponge
04.11.22 16:26 04.11.22 16:26