Heating Water; Cleaning And Maintenance - RONDELL RDE-1109 Bedienungsanleitung

HEATING WATER

– Place a cup under the coffee spout (2) of the coffee
machine and adjust its height (pic. 4).
– Press the button (20) « » to heat water.
– The hot water supply will stop automatically when its vol-
ume in the cup reaches 250 ml. Press «Exit» button (21)
« » to stop hot water supply.
MAKING DRINKS FROM GROUND COFFEE
– Add 2 coffee spoons (10 g) to the ground coffee funnel (9).
ATTENTION! The amount of ground coffee to be added
should not exceed 2 spoons, the spoon is supplied with the
unit. Otherwise, the coffee powder will spill out of the brew-
ing unit, causing it to clog and damage.
– Press «Ground coffee» button (21) «
sponding symbol will appear on the display (pic. 15).
– Press the selected beverage button «Espresso» (19) «
or «Americano» (18) « ».
– The drink making process will end automatically.
Below is the table on making drinks:
Drink name Ground Ready
beans drink
weight, amount,
g ml
Espresso
One cup/ 9-11 20-120
two cups
Default 10
Americano
One cup/ 9-11 20-200
two cups
Default 10
FUNCTION CAPABILITIES
Grinding degree control
Adjust the grinding degree (from 1 to 5) of the coffee beans
while the coffee grinder is running.
If you turn the knob (14) counterclockwise, the grind size
will be finer and the taste of coffee will be stronger.
If you turn the knob (14) clockwise, the grind size will be
coarse and the taste of coffee will be weak.
ATTENTION! The coffee grinder should only be adjusted
while the coffee grinder is in operation. Failure to do so may
result in unit damage.
», the corre-
»
Tem- Hot
pera- water,
ture, °С ml
75-95 –
40 85 –
75-95 0-200
40 85 80
20
Drip tray (1)
– When the level of the drained liquid rises to the upper
limit, the float water level indicator rises, after which it is
required to drain the liquid from the drip tray.
– If the display shows «No drip tray» «
installed, remove the drip tray and reinstall it.
Brewing unit (12)
– Please do not open the door (11) or move the brewing
unit (12) during coffee making. If the display (17) shows
«No brewing unit» « », please remove it and then rein-
sert it into its place until it clicks.
– If the display shows the «Brewer unit door is open
symbol, open and then close the door (11) tightly.
Used coffee grounds container (13)
– When the symbol « » appears on the display, please
empty the container (13).
Changing the coffee machine settings
You can change the beverage making settings only during
making it.
– Press and hold the button (21) «
the coffee making settings.
– Set the water temperature from 75 to 95°C by pressing
the buttons (18) « » or (20) «
– Press the button (21) « » and set the automatic switch-
off time in the range from 0.5 to 24 hours by pressing the
buttons (18) « » or (20) «
– To reset to the factory settings, press the button (21) «
(pic. 19), then press and hold down the button (18) «
or (20) « ». If you do not want to reset, press the button
(21) « » again: you will enter the device information view
mode (the date of manufacture of the coffee machine and
the batch number will be displayed) (pic. 20).
– Press the button (21) « » to exit the settings mode.

CLEANING AND MAINTENANCE

Washing the milk frothing system
– Place a cup with clean water under the cappuccina-
tor pipe.
– Press the button (23) « » (pic. 12) and clean the cap-
puccinator pipe.
– After the rinse is finished, let the coffee machine cool
down for 15 minutes.
– Remove the cappuccinator pipe (3) (pic. 21) and wash it
under a water jet.
» with the drip tray
»
» for 4 seconds to set
» (pic. 17).
» (pic. 18).
»
»