Basic Operations - Makita UT001G Betriebsanleitung

Operation of speed change knob
NOTICE:
Use the speed change knob only after
the tool comes to a complete stop. Changing the
tool speed mode before the tool stops may damage
the tool.
NOTICE:
Always set the speed change knob
carefully into the correct position. If you operate
the tool with the speed change knob positioned half-
way between the position 1 and the position 2, the
tool may be damaged.
NOTICE:
If the rotation speed significantly
decreases during operation in the high speed
mode, stop the tool and change the mode to the
low speed mode. Otherwise, the motor may get
overloaded and cause a malfunction or fire.
Two speed ranges can be preselected with the speed
change knob.
Select the proper speed mode for the material to be
mixed.
To change the speed mode, turn the speed change
knob so that the pointer points to the dot at position
1 for low speed mode or the dot at position 2 for high
speed mode.
► Fig.16: 1. Pointer 2. Speed change knob 3. Dot
Operation of speed adjusting dial
The tool speed can be adjusted steplessly by turning
the speed adjusting dial. The no load speed when the
switch trigger is fully pulled can be adjusted 270 min
-1
to 500 min at low speed mode, 500 min
at high speed mode. Higher speed is obtained when
the dial is turned in the direction of number 5; lower
speed is obtained when it is turned in the direction of
number 1.
Select the proper speed for the material to be mixed.
► Fig.17: 1. Speed adjusting dial
NOTICE:
The speed adjusting dial can be turned
only as far as 5 and back to 1. Do not force it past
5 or 1.
Accidental restart preventive
function
If you install the battery cartridge while pulling the
switch trigger or locking the switch trigger, the tool does
not start. To start the tool, release the switch trigger, and
then pull the switch trigger.
Electronic function
The tool is equipped with the following electronic func-
tion for easy operation.
Soft start
The soft-start function minimizes start-up shock, and
makes the tool start smoothly.

Basic operations

operate the tool around flammable materials such
as paint with thinner used as solvent. Failure to do
so may cause an injury.
in the high speed mode. You may lose the control of
the tool and cause an injury.
outside the stirring vessel.
during use, turn off the switch and stop using the
tool.
NOTICE:
mixing blade floating out of the material, be care-
ful not to splash the material.
NOTICE:
other than stirring mortar, concrete, etc.
1.
according to the material to be mixed.
2.
blade under material fully. Check that the material is not
solidified and the safety of the work site, then turn on the tool.
3.
ing operation so that whole part of material can be mixed.
4.
-1
that the mixing blade has come to a complete stop, and
-1 -1
to 920 min then pull it out of the mixing container.
Applied operations
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Replacing battery cover
Optional accessory
Install one of the battery covers to fit the size of your
battery cartridge.
► Fig.18: 1. Battery cover S 2. Battery cover L
1.
pressing the button on the battery cover.
2.
battery cover. Then remove the screw, sleeve and the
battery cover.
► Fig.19: 1. Screw 2. Sleeve 3. Battery cover (stan-
NOTE: The sleeve may remain in the mounting holes.
In that case, pull it out using a screw or the like.
3.
cover with the mounting holes on the housing. Insert the
sleeve. Then tighten the screws to secure it in place.
► Fig.20: 1. Screw 2. Sleeve 3. Battery cover (optional)
4.
11 ENGLISH
CAUTION:
Do not mix flammable materials or
CAUTION:
Do not mix high viscosity material
CAUTION:
Do not rotate the mixing blade
CAUTION:
If you hear an abnormal noise
When you mix the material while the
Do not use the tool for any purpose
Select high speed mode or low speed mode
Hold the tool firmly with both hands. Place the mixing
Move the mixing blade up and down during the mix-
When finishing mixing, turn off the tool. Make sure
CAUTION:
Always be sure that the tool is
3. Button
Open the standard equipped battery cover while
Loosen the screw securing the standard equipped
dard equipped)
Align the mounting hole on the optional battery
Close the battery cover securely.