cecotec DRUMFIT CYCLE 9000 TALOS PRO Bedienungsanleitung Seite 25

ENGLISH
- Carefully check the pieces are not damaged. If they are, immediately notify the Technical
Support Service of Cecotec.
Box contents
- DrumFit Cycle 9000 Talos Pro stationary bike
- LCD monitor
- Tools
- Instruction manual
- Power adapter
3. ASSEMBLY
Scanning the following QR code, you can view the complete
assembly, step by step, of the product.
Step 1: Anti-roll bars
- Take the anti-roll bars:
- The bar with the casters is the front anti-roll bar.
- The bar without the casters is the rear anti-roll bar.
- Place the main frame (12) on the front anti-roll bar (11) by matching the holes. Insert the
Allen screw (19) with the flat washer (20) in every hole and tighten them.
- Repeat the previous process with the rear anti-roll bar (9).
Fig. 3
Step 2: Pedals
- The pedals are marked "L", left pedal (10), and "R", right pedal (7).
- Place the right pedal (7) on the right crank, in the direction of the bike, and tighten the nut
by turning the double open-end spanner (22) clockwise.
- Place the left pedal (10) on the left crank, in the direction of the bike, and tighten the nut by
turning the double open-end spanner (22) counterclockwise.
Fig. 4
Step 3: Saddle post and saddle
- Insert the saddle (6) into the saddle sliding set (4), and fix it with the double open-end
spanner (22).
- Slide the saddle (6) and the saddle sliding set (4) in the desired position, match the holes
and fix it with the saddle distance adjustment knob (27).
- Insert the saddle post (5) in the main frame (12) and match the holes on both pieces. Fix
the saddle position (6) with the saddle height adjustment knob (28). You can set the height
when the bike is completely assembled.
Fig. 5
Step 4: Handlebar post
55
- Insert the handlebar post cover (13) in the handlebar post (15).
- Connect the cable protruding from the main frame (12) to the cable (14) inside the
handlebar post (15). Insert the post (15) in the main frame (12) as shown in figure 6 and
match the holes with both pieces.
- Insert a flat washer (20) in the 4 Allen screws (19), and tighten them in every hole. Insert
them in the holes of the handlebar post (15) with the Allen key (21). Place the handlebar
post trim (13) to cover this part.
- Place the bottle holder (18) in the handlebar post (15) as shown in figure 6, that is, matching
the holes on both pieces. Use two flathead crosshead screws (23) to fix the bottle holder
(18) to the handlebar post (15).
Fig. 6
Step 5: Handlebar
- Take the handlebar (1) and assemble it on the handlebar support (16). Fix the handlebar
support with a screw (19), a small flat washer (24) and a spring washer (25). Insert the
heart rate sensor cables (29) in the handlebar post hole and then take them out in the
other end where the monitor holder is located (17).
- Place the handlebar cover (3) by applying pressure until it is fixed in place.
Fig. 7
Step 6: LCD monitor
Connect both ends of the monitor cable (14) with the heart rate sensor cables (29). Place the
LCD monitor (2) on the monitor holder (17) by inserting the cables through the hole of the
monitor bracket (17). Secure both parts using 4 flathead crosshead screws (26) and the Allen
key (21).
Fig. 8
4. OPERATION
Monitor operation
Button functions
- RECOVERY: press this button to activate the recovery function. This function is used to test
your heart rate recovery level.
- START/STOP: press this button to start and stop the training.
- RESET: press this button:
a. When the bike is on standby, to go back to the main menu.
b. For 2 seconds to restart the monitor.
- UP, press this button:
a. To select the training mode.
ENGLISH
DRUMFIT CYCLE 9000 TALOS PRO
56