Inhaltsverzeichnis
Werbung
MAXIMALE FLIESENGRÖSSEN (NUR D36000)
Materialtyp
Größe (bis zu)
Max. Gewicht
cm
Fliese
60x60x1,0
9 kg
Fliese
90x90x1,0
20 kg
Fliese
94x20x1,0
4,5 kg
Fliese
94x20x1,0
4,5 kg
Fliesenleger
30,5x30,5x5,0
11,7 kg
Ziegel
21,5x10,2x6,5
3,1 kg
Schließen des Fliesensägengestells
1. Trennen Sie die Fliesensäge von der Stromversorgung.
2. Umbauen der Fliesensäge für den Transport.
3. Nehmen Sie die Nassfliesensäge vom Gestell ab.
4. Heben Sie das Gestell an den oberen Schienen auf und klappen Sie sie zum
Schließen herein.
English
D240001 Tile Saw Leg Stand
WARNING: For your own safety, read the tile saw instruction manual before mounting
any accessory. Failure to heed these warnings may result in personal injury and serious
damage to the tile saw and the accessory. When servicing this stand, use only identical
replacement parts.
Technical Data
Max. Height
Min. Height
Width
Max. load
Weight
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
WARNING: The use of any accessory or attachment or performance of any operation
with this tool, other than those recommended in this instruction manual may present a
risk of personal injury.
WARNING: Never modify the tile saw leg stand or any part of it. Damage or personal
injury could result.
GENERAL SAFETY INSTRUCTIONS FOR TILE SAW LEG STAND
WARNING: To reduce the risk of personal injury:
1 . Follow the mounting instructions carefully. Fasten the saw to the stand securely as
instructed. Proper assembly is important to prevent the risk of a collapse of the saw stand.
2 . Ensure all stand fasteners are securely fastened and that all stand mechanisms
are in proper working order before mounting or operating the table saw. Proper
assembly is important to prevent the risk of a collapse of the saw stand.
3 . Attach the power tool securely to the saw stand before using it. Sliding off of the
power tool on the saw stand can lead to loss of control.
4 . DO NOT use the stand on uneven surfaces. The stand is designed to be used on a
flat, stable surface. If the saw stand can slide around or wobbles, the power tool or the
workpiece cannot be evenly and securely guided.
5 . Pull the plug from the mains receptacle and/or remove the battery from the
power tool before making adjustments on the tool or changing tool accessories.
Unintentional switching on of the power tool is the cause of many accidents.
6 . Ensure that long and heavy workpieces do not affect the balance of the saw stand.
Long and/or heavy workpieces must be supported at the free end.
7 . Keep your fingers clear of the hinge points while folding the legs of the saw stand.
Danger of fingers being crushed or contused.
8 . Do not overload the saw stand and do not use it as a ladder or scaffolding.
Overloading or standing on the saw stand can lead to personal injury.
9 . Do not use the saw stand if it is damaged or bent. Deteriorated stability of the saw
stand can lead to personal injury.
10 . Have your power tool attachment repaired by an authorised D
Repair of your power tool attachment being a matter of precision and skill, always take it to
your authorised D
WALT repair agent.
e
Schnitte
Position des
Sägewagen-
Anschlagknopfes
Längs- oder
2
Querschnitt
Längs- oder
1
Querschnitt
Längsschnitt
1
Querschnitt
2
Längs- oder
2
Querschnitt
Längs- oder
2
Querschnitt
D240001
mm
835
mm
710
mm
640
kg
136
kg
7.8
WALT repair agent.
e
Markings on Stand
The following pictograms are shown on the stand:
Read instruction manual before use.
DO NOT exceed the weight this stand can hold. The D240001 tile saw stand is
136kg
designed to support 136 kg safely in a work environment.
DO NOT climb, sit or stand on the stand.
DO NOT drop heavy loads on the stand.
Intended Use:
This tile saw stand is designed for use with D
Package Contents
The package contains:
1 Tile saw leg stand
4 Leg extensions
4 Hex head bolts
8 Flat washers
4 Spring washers
4 Hex nuts
1 Instruction manual
•
Check for damage to the tool, parts or accessories which may have occurred
during transport.
•
Take the time to thoroughly read and understand this manual prior to operation.
Description (Fig. A)
The tile saw leg stand D240001 has been designed to extend the versatility of your D
tile saw.
Support bar
1
2
Leg
Leg extension
3
ASSEMBLY AND ADJUSTMENT
Setting Up the Leg Stand (Fig. A, B)
The leg extensions have a series of holes to allow multiple stand heights.
1. Place the leg stand upside down on the floor.
2. Unfold the legs
2
.
3. Fit a leg extension
3
into each leg
2
.
4. Align the holes in the leg and the extension at the required height.
5. Insert a hex head bolt
4
through a flat washer
6. Place a flat washer
, a spring washer
5
head bolts.
7. Place the stand in an upright position.
8. Tighten the nuts.
9. Check that the stand is stable. Make sure that the leg extensions are adjusted to the
same height.
To Use Tile Saw Stand
D24000 (Fig. A, C, D)
1. Unfold the saw stand until it is fully opened. Place it upright, as shown in Figure A.
2. Place the Wet Tile Saw pan
8
on the stand. The rear feet on the pan have two semi-
circular reliefs
9
; place these over the rear rail as shown in Figure C. The front rail should
rest behind the front feet on the pan.
Maximum Tile Size: 63.5 cm x 63.5 cm x 1.2 cm
D36000 (Fig. A, E, F)
CAUTION: ALWAYS make sure the pan stand bracket is rotated as shown in Fig. E to
keep the saw from tipping forward off the stand.
CAUTION: Tip Hazard. Excessive weight on the cart when the cart position knob
is rotated to position 1 could cause a tip hazard. Maximum tile size that can be cut
is 90 cm x 90 cm x 1.0 cm (refer to Maximum Tile Size). Do not cut tile or other
materials that are thicker than 1 cm thick while the cutting cart stop knob is in position
1. When cutting narrow materials, rotate the cutting cart stop knob to position 2.
This will allow the cart to stay on the rail when pulled toward the user in front of the
cutting wheel.
CAUTION: Always lock cutting cart before moving or transporting saw.
1. Unfold the saw stand until it is fully opened. Place it upright, as shown in Figure A.
2. Place the saw into the stand as shown in Figure E. The pan has two brackets
wrap around the front cross bar.
3. Rotate the pan stand bracket
11
in place around the rear cross bar.
WALT D24000 and D36000 Tile Saws.
e
5
and into the holes.
and a nut
onto the end of each of the hex
6
7
10
that
WALT
e
Werbung
Inhaltsverzeichnis
