Monacor EAM-17DT Bedienungsanleitung Seite 4

EAM -17 DT
THE AUDIO COMPANY THE AUDIO COMPANY THE AUDIO COMPANY THE AUDIO COMPANY THE AUDIO COMPANY THE AUDIO COMPANY THE AUDIO COMPANY THE AUDIO COMPANY THE AUDIO COMPANY
6) In the field "Rename Device", the name
used for the device in the Dante network
can be changed (e. g. to a specific name with
a reference to the installation location). Con-
firm with "Apply".
7) If necessary, adjust the "Sample Rate" to the
desired Dante receiver or set a different com-
mon sample rate for both devices.
8) The tab "Network Config" can be used to
change the network configuration for the
Dante interface of EAM-17DT if required.
4.2 Routing with the Dante Controller
In the "Network View" window under the tab
"Routing", the transmitters of the Dante net-
work are arranged in columns ("Transmitters")
and the receivers in rows ("Receivers"). This
matrix can be used to assign the transmission
and receiving channels of the devices to each
other.
1) In the row of the desired Dante receiver,
⊞
click to show its receiving channels and
in the column of EAM-17DT, click
its transmission channels (
2) Starting from the column of the desired
transmission channel of EAM-17DT, navigate
to the row of the desired receiving channel
and click the field at the intersection.
3) Wait until the field shows a green circle with
a white tick symbol ✔.
➃
Routing from EAM-17DT to WALL-05DT
An English user guide for the Dante Controller
can be downloaded from the Audinate website
at:
www.audinate.com/learning/technical-documentation
5 Operation
The LED (1) lights up as soon as the device is
supplied with power via its network connec-
tion. The colour of the LED will indicate the
operating status:
red: the microphone is mute
green: the microphone is on
The function of the talk button (2) depends on
the setting MODE in the configuration soft-
☞
ware ( chap. 5.1).
5.1 Settings via the software
For EAM-17DT, some settings can be made via a
configuration program available for download
from the Monacor website (www.monacor.com).
Order No. 1000903
For setting up EAM-17DT via the program,
connection to a Dante network is not required.
It is sufficient to connect the microphone to a
PC via a PoE switch if the network connection
of the PC is set to DHCP.
After starting the program, the following win-
dow will appear:
➄
Start screen
1) Click the button DISCONNECTED. All EAM-
17DT devices found in the network will be
listed and the button will change to CON-
NECTED. The device names from the Dante
network will be listed under NAME.
2) Double-click the desired microphone on the
list. The configuration window will open on
the left.
⊞
to show
☞
fig. 4).
EAM-17DT-07f928
➅
Configuration window and device list
GAIN: to set the gain in dB (volume); the ver-
tical bar graph above MUTE will show the cur-
rent signal level
MODE: to select the operating mode of the
talk button (2)
ON:
OFF: briefly press the button to mute the
PTT:
PTM: to mute the microphone, keep the
MUTE will indicate the operating status [like
LED (1)]; click MUTE: to switch microphone on/
mute (only if MODE = ON or MODE = OFF)
Click CALL: to identify a microphone, its LED (1)
will flash for 10 seconds
LOWCUT: high-pass filter to suppress impact
noise (structure-borne noise)
Click �: to close the configuration window
Copyright © by MONACOR INTERNATIONAL
All rights reserved
A-2135.99.02.10.2022
ID NAME
ID NAME
1 EAM-17DT-07f928
2 EAM-17DT-83f73e
briefly press the button to switch the
microphone on or to mute it again
(initial state = mute)
microphone or to switch it on again
(initial state = on)
to talk, keep the button pressed (push
to talk)
button pressed (push to mute)
MONACOR INTERNATIONAL GmbH & Co. KG
Zum Falsch 36, 28307 Bremen
Germany
6 Specifications
Microphone type: . . . . . back-electret
(array consisting of
17 capsules)
Frequency range: . . . . . 80 –20 000 Hz
☞
Directionality: . . . . . . . . figs. 8, 9
max. SPL: . . . . . . . . . . . 106 dB
Dante output signal
Number of channels: 2
Resolution: . . . . . . . . 16 – 32 bits
Sampling rate: . . . . . 44.1 – 96 kHz
Data interface
Ethernet: . . . . . . . . . RJ45 connector
Power supply
Power over Ethernet: PoE according to
IEEE 802.3af-2003
Power consumption: 2.3 W
Housing material: . . . . . metal
Ambient temperature: . 0 – 40 °C
Dimensions (W × H × D): 348 × 31 × 60 mm
Weight: . . . . . . . . . . . . 386 g
dB
0
−10
−20
−30
➆
20 50 100 200 500 1k
Frequency response
0°
330° 30° 30°
300° 60°
270° 90°
240° 120°
150°
210°
➇
180°
Polar pattern, horizontal
0°
330° 30° 30°
300° 60°
270° 90°
240° 120°
150°
210°
➈
180°
Polar pattern, vertical
Subject to technical modification.
2k 5k 10k 20k
Hz