Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
LED Orientation Light (Receiver)
Item no: 2377687
1 Intended use
The product is a battery-operated wall light. The wall light supports two operation modes. In manual
mode, the light is controlled by a mechanical switch. In automatic mode, the wall light will be triggered by
another wall light with motion sensor (PIR) on the same frequency channel when motion is detected.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to
third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.
2 Delivery contents
■
1x Wall light
■
Operating instructions
3 Latest product information
Download the latest product information at
low the instructions on the website.
4 Description of symbols
The symbol with the exclamation mark in the triangle is used to indicate important informa-
tion in this document. Always read this information carefully.
This product must only be used in dry, enclosed indoor areas. It must not become damp or
wet.
This product is constructed according to protection class III.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety informa-
tion. If you do not follow the safety instructions and information on proper handling,
we assume no liability for any resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
5.1 General
■
The product is not a toy. Keep it out of the reach of children and pets.
■
Do not leave packaging material lying around carelessly. This may become dangerous playing mater-
ial for children.
■
If you have questions which remain unanswered by this information product, contact our technical
support service or other technical personnel.
5.2 Handling
■
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
■
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
■
Consult an expert when in doubt about the operation, safety or connection of the appliance.
5.3 Operating environment
■
Do not place the product under any mechanical stress.
■
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
■
Protect the product from high humidity and moisture.
■
Protect the product from direct sunlight.
■
Do not switch the product on after it has been taken from a cold to a warm environment. The con-
densation that forms might destroy the product. Allow the product to reach room temperature before
you use it.
■
Never operate the product in direct proximity of strong magnetic or electromagnetic fields or transmit-
ter aerials or HF generators. Doing so can prevent the product from functioning properly.
3
www.conrad.com/downloads
or scan the QR code shown. Fol-
5.4 Batteries
■
Correct polarity must be observed while inserting batteries.
■
The batteries should be removed from the device if it is not used for a long period of time to avoid
damage through leaking. Leaking or damaged batteries might cause acid burns when in contact with
skin, therefore use suitable protective gloves to handle corrupted batteries.
■
Batteries must be kept out of reach of children. Do not leave batteries lying around, as there is risk,
that children or pets swallow them.
■
All batteries should be replaced at the same time. Mixing old and new batteries in the device can lead
to battery leakage and device damage.
■
Batteries must not be dismantled, short-circuited or thrown into fire. Never recharge non-rechargeable
batteries. There is a risk of explosion!
5.5 LED light
■
Do not look directly into the LED light!
■
Do not look into the beam directly or with optical instruments!
6 Installing batteries
Note:
If an insulating strip protrudes from the battery compartment, batteries are installed already. Pull the
strip out to establish the power supply.
P
:
RECONDITIONS
a
Prepare the required number of batteries of the correct type as stated in the section "Technical data".
1. Unlock the battery compartment cover and remove it.
2. Insert the batteries into the battery compartment observing the polarity markings in the compartment.
3. Attach the compartment cover and lock it. If a seal is present, make sure it sits correctly and you do
not damage it when attaching the cover.
7 Mounting
7.1 Selecting mounting locations
Select a mounting location under consideration of the maximum wireless range (6 m) and factors that can
reduce the wireless range.
Surrounding objects can reduce the strength of the wireless signal:
■
Walls and reinforced concrete ceilings
■
Coated or vaporised insulating glass panes
■
Proximity to metallic and conductive objects (e.g., radiators)
■
Broadband interference, e.g. in residential areas (DECT phones, mobile phones, radio headsets,
wireless speakers, wireless weather stations, baby monitoring systems, etc.)
■
Electric motors, transformers, power-supply units and computers
■
Poorly shielded or uncovered computers or other electrical appliances
7.2 Mounting with screws
Mount the light using screws and wall plugs.
WARNING
Concealed wires. Risk of deadly electric shock when drilling.
● Check for concealed wires before drilling.
1. Drill holes and insert wall plugs.
2. Use screws to fix the mounting plate in place.
3. Hang the light on the mounting plate.
7.3 Mounting with double-sided tape
Mount the light using double-sided tape.
1. Remove the protective backing from the tape.
2. Stick the tape onto the mounting plate.
3. Remove the second backing and stick the mounting plate onto the mounting surface.
4. Hang the light on the mounting plate.
8 Operation
Operate the light in manual or automatic mode. In manual mode you switch the light on and off manually.
In automatic mode, the light is switched on by another light with motion detection and switched off by the
built-in timer.
Note:
Replace the batteries as soon as you notice poor performance.
8.1 Operating in manual mode
Use the switch ON/OFF/AUTO to switch the light on and off.
1. To switch the light on, move the switch ON/OFF/AUTO to ON.
2. To switch the light off, move the switch ON/OFF/AUTO to OFF.
8.2 Operating in automatic mode
In automatic mode, lights on the same channel frequency communicate with each other. If a light with mo-
tion sensor detects movement, it tells the other lights to switch on as well.
1. On all lights, move the switch CHANNEL to the same channel number.
2. On all lights, move the switch ON/OFF/AUTO to AUTO.
à
When motion is detected, the lights switch on.
After 60 seconds, all lights go out if no further motion is detected.
Werbung
Inhaltsverzeichnis
