Inhaltsverzeichnis
Werbung
7. Technische Daten
(send / return)
Mono jack, ¼" (6.35 mm)
Footswitch ON: Effect is OFF
footswitch (2)
Connector for footswitch selecting master volume
Mono jack, ¼" (6.35 mm)
Footswitch OFF: Ensemble
Footswicht ON: Solo
footswitch (3)
Connector for dual footswitch for channel muting
Stereo jack, ¼" (6.35 mm)
Tip = muting for ch 1
Ring = muting for ch 2
Sleeve = common (ground)
Footswitch ON: Channel is muted.
The mute switches are not in effect while the footswitch
is connected.
Tone controls
channel 1
colour
–3 dB at 700 Hz / +10 dB at 8 kHz
contour
0 ... +6 dB at 10 kHz (shelf type)
bass
±10 dB at 85 Hz
middle
±10 dB, at 330...1000 Hz (adjustable)
treble
±10 dB at 10 kHz
channel 2
bass
±8 dB at 100 Hz (shelf type)
middle
±6 dB at 800 Hz
treble
±8 dB at 10 kHz (shelf type)
notch filter Frequency
60...400 Hz, adjustable
Gain
–13 dB
Bandwidth
0.7 octaves at –6.5 dB
Effects
compressor
Type RMS-responding, soft-knee, gain reduction
Threshold
ca. –40...+10 dB (adjustable)
ref. to nominal output voltage
Ratio 1:1 ... 1:5 (adjustable)
at 20 dB gain reduction
RMS time constant 40 ms
External effects
Parallel loop (see send and return)
Serial loop (see insert point)
Power amp construction
Discrete bipolar-transistor output
Output power 2 x 100 W / 8 Ω (THD = 1%)
driving 4 loudspeakers, 50 W each.
Continuous output power is determined by the limiter,
see limiter threshold
General
Distortion
THD + N < 0.1% (2 x 10 W / 8 Ω), measured at
loudspeaker terminals
Noise
Residual noise (A-weighted):
Referred to nom. output power: –100 dB
Acoustical: approx. 16 dB SPL / 1 m
Analog signal processing
Subsonic filter, RMS limiter, speaker equalization with
harmonics exciter
Limiter threshold
2 x 75 W / 8 Ω
Speaker system
2 x 8" (200 mm) dual cone full-range speakers
(front side)
2 x 8" (200 mm) woofers (inside)
Dual-chamber bass reflex cabinet
Mains power
Mains voltage (depending on model):
100, 120, 220, 230, or 240 V~, 50–60 Hz
Power consumption: max. 350 W
Mains fuse, size: 5 x 20 mm
For 220, 230, 240 V models:
T 3.15A L 250V
For 100 and 120 V models:
T 6.3A L 250V
Operating temperature range
0...35 °C
Cabinet
15 mm (0.59") birch plywood
Finish
Waterbased acrylic, black spatter finish
Dimensions and weight
490 mm (19.3") high
360 mm (14.2") wide
405 mm (15.9") deep
Weight
23 kg (51 lbs)
NOTES
Options configurable by internal jumpers (refer modification to qualified
personnel): low-gain option (more headroom) for mic input
Aux signal can be removed from DI out
DEFINITIONS
Rated conditions
Nominal input voltage at input under test
master (ensemble) fully clockwise
high / low, colour, notch, and compressor oft
contour fully anticlockwise bass / middle / treble / pan centered
gain of unused inputs fully anticlockwise
gain of input under test adjusted to nominal output voltage at line out.
(This condition corresponds by design to the rated output power.)
Nominal input voltage: Standard condition for specifications, if not stated
otherwise.
Minimum input voltage: Input voltage required for nominal output with
maximum gain and volume settings.
Maximum input voltage: Input voltage that does not cause distortion
more than rated THD+N, suitable control settings provided.
Nominal output voltage or power refers to rated conditions.
THD + N: Total harmonic distortion + noise, input voltage reduced by 10
dB after setting up rated conditions.
Signal / noise ratio: Ratio of output voltage at rated conditions to output
noise voltage with input shorted.
Equivalent input noise voltage: Noise voltage at loudspeaker terminals di-
vided by gain of amplifier. Input shorted after setting up rated conditions.
Residual noise: Output noise with minimal gain and volume settings.
Compression ratio of soft-knee compressor varies with gain reduction.
Therefore the gain reduction is also specified.
General: Signal voltages are RMS values. Test signal sine 1 kHz sine unless
stated otherwise. Noise measured from 20 Hz to 20 kHz. Noise stated for
a specific input implies that all other inputs are not used. Sound pressure
level (SPL) based on loudspeaker specification by manufacturer.
Specifications and appearance subject to change without notice.
TD20161208 (Basic performer 2)
Versions-InformationBasic performer 2
Board 1 Rev. B Ver. 4
Board 2 Rev. B Ver. 4
Board 3 Rev. B Ver. 4
ndstufe Rev. B Ver. 7
Daten meßtechnisch geprüft: HHB 08.12.2016
9
Werbung
Inhaltsverzeichnis
