Product Handling - Sthor 78118 Bedienungsanleitung

GB
The drill and automatic return screwdriver is provided with an unloaded battery, so before work may commence, it is
required to charge it following the procedure below, using the charger and charging dock provided. Li-ION batteries
do not show the so called "memory effect", so it is allowed to charge them at any moment. However, it is recom-
mended to discharge them during normal work, and then load them to their full capacity. If due to the nature of the
task it is not possible to do so each time, then it is required to do it at least from time to time. Under no circumstances
is it allowed to discharge the batteries short-circuiting the electrodes, since this would cause irreversible damage! It
is also prohibited to check the load of the batteries, short-circuiting the electrodes for sparking.
Storage of the battery
In order to prolong the life of the battery, it is required to provide adequate storage conditions. The batteries can go
through approximately 500 „loading - discharging" cycles. The battery must be stored between 0 and 30°C, at the
relative humidity of 50%. In order to store the battery for a prolonged period, it is required to charge it to approxi-
mately 70% of its capacity. In case of prolonged storage, it is required to recharge the battery once a year. Do not
permit excessive discharging of the battery, since this would reduce its life and may cause irreversible damage.
During storage, the battery will be gradually unloading due to leakage conductance. The process of automatic un-
loading depends on the temperature of storage, since the higher the temperature, the fastest the process. In case
of incorrect storage of batteries, there is a danger of electrolyte leakage. In case of leakage, it is required protect the
leakage with neutralizing agent. In case of contact of electrolyte with the eyes, it is required to rinse the eyes abun-
dantly, and then immediately seek medical assistance. It is prohibited to use a tool with a damaged battery.
In case the battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such
waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may
transport the tool with the battery or only batteries by land. Then no additional conditions must be complied with. In
transport is realised by third parties (for example dispatch through courier service), then it is required to proceed in
accordance with regulations for transport of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the
exposed contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the pack-
age during transport. It is also required comply with the national regulations for transport of dangerous materials.
Battery charging
Note! Prior to charging, unplug the charger of docking station from the mains, by pulling off the plug of the charger
from the mains socket. Also clean the battery and its terminals of dirt and dust using soft and dry cloth.
Disconnect the battery from the tool by pressing the latch or both latches at the same time, and then slide it out from
the battery socket.
Plug the charger to battery's socket (II)
Plug the charger to mains.
The diode lights up which indicates the start of charging process.
After charging is finished, the diode changes its colour from red to green, which indicates power supply to the
charger.
Pull off the charger plug from the mains socket, and the plug of the charger cable should be disconnected from the
battery.

PRODUCT HANDLING

Press the switch button to switch on the lamp. Pressing the switch again results in lamp switch off.
The lamp has a reflector, the position of which may be adjusted (III). It is possible to set it in few positions, each set-
ting is indicated by a sound of a latch, the so-called "click".
The lamp may be positioned using the battery as the base.
MAINTENANCE AND OVERHAUL
ATTENTION! Before any adjustment, technical service or maintenance operations unplug the tool. Once the opera-
tions have been finished, the technical conditions of the tool must be assessed by means of external evaluation and
inspection of the following elements: body and handle, conductor with a plug and deflection, functioning of the electric
9
O R I G I N A L I N S T R U C T I O N S