Technical Data - YATO YG-04301 Originalanleitung

Attention! Water in the boiling pot may be heated to a high temperature, be careful during the water distribution, in order to avoid
burns.
During operation you should continuously control the level of water in the device, and to complement it when needed.
When you fi nish your work, switch off the product by switch, remove the power cable plug from the mains socket. then empty the
tank of the product and proceed to maintenance.
If during its operation the product would run out of water or it accidentally its power supply would turn on when the tank is empty,
temperature protection would be activated. Then you should turn off the product, and then remove the plug of power cable from
the mains wall socket. Empty the water tank and press the reset button located on the bottom of the product. Then fi ll the tank with
water, connect the product to the power supply and run it normally.
Emptying the product of water
Attention! Before emptying the product of water, you should turn off the product, and the plug of power cable disconnect from the
mains socket. It is also recommended to leave water in the product till it cools down..
The product should be drained of water using the tap. Drain all water into a separate container, then remove the product cover and
dry the product interior with a dry soft cloth or leave it to dry.
It is forbidden to empty the tank of the product by pouring water through its upper edge.
Maintenance of the product
Due to the use of the product for the storage of water, which is intended for human consumption, the product should be carefully
maintained. This will allow to keep the proper hygiene. The product must be subjected to maintenance after each use.
Before each cleaning, turn off the product, disconnect the plug of power cable from the mains wall socket. drain it of water, and
then wait for its cooling down and only then proceed to maintenance.
To clean the product, you should use only mild agents intended to clean kitchen utensils. It is forbidden to use abrasive cleaners for
example powder or cleaner milk, which is containing corrosive substances. Do not use cleaning solvents, gasoline or alcohols.
Cleaner should be diluted with water accordance to the information that came with it, then apply on a soft cloth and clean the
product from inside and outside.
Residues of the cleaning agent should be removed from the outside with a soft cloth soaked in water, then wipe it dry. The Interior
of the product should be rinsed with clean water and dry or let to dry.
ATTENTION! The product is not intended for cleaning with a stream of water. Do not immerse the product in water.
If the product there are accumulated limestone deposits, precipitated of water as so called "stone", you should remove them.
Stone deposits do not represent a hygienic threat to water, but they can change its fl avor and reduce the performance of the
device. Too large a buildup of sediments can lead to damage to the product, therefore, you should regularly remove them.
The product should be fi lled with water, and then add the vinegar or product for removing limescale from products for the prepara-
tion of water intended for human consumption. Mount the cover, then boil the water in the product.
After boiling it, you should drain a little water through the tap, which will allow to rinse it from stone deposits. The remainder of
water should be boiled several times, until the complete removal of sediments.
After complete removal of the sediments you should disconnect the product from mains, fl ush the Interior with a cleaning solution,
and then the rinse its Interior repeatedly with clean water.
Attention! If the fi tered water will be used in the product, this should signifi cantly reduce the formation of calcareous deposits.
Storage of the product
If the product will not be used for an extended period of time, you should completely remove water, and thoroughly dry its Interior.
Store the product indoors, protect against dust, dirt and moisture. It is recommended to store the product in the factory packaging.
Store the product in its working position. Do not install the products in layers. Do not place anything on the product.

TECHNICAL DATA

Parameter
Catalog number
Rated voltage
Rated frequency
Rated power
Insulation class
Rated capacity
Working temperature
Net weight
O R I G I N A L
10
Unit
YG-04301
[V] 230~
[Hz] 50
[W] 900 - 1000
I
[l] 8.8
[ O C] 30 ÷ 110
[kg] 2.0
GB
Value
YG-04310 YG-04315
230~ 230~
50 50
1400 - 1650 1500 - 1800
I I
10 15
30 ÷ 110 30 ÷ 110
2.1 2.6
I N S T R U C T I O N S
YG-04318 YG-04324
230~ 230~
50 50
2100 - 2600 2500 - 3000
I I
18 24
30 ÷ 110 30 ÷ 110
2.9 3.2