Werbung
OPTOTRONIC
LED Power Supply
®
22)
Position
24)
A or B
C
D
Installing and operating information (built-in LED power supply): Connect
only LED load type. LED module will be switched off when output voltage is
outside the voltage range given on the driver. Wiring information (see fig. A): Do
not connect the outputs of two or more units. The metal surface on LED driver
underside of OT Wi 40 NFC BL LP I is double insulated against mains, also the
metal surface is SELV basic insulated against LED output. Output current adjust-
ment = via programming software using Near Field Communication (NFC) in mains
off mode only. For Near Field Communication (NFC) please refer to Tuner4TRON-
IC at www.osram.com/ds. Unit is permanently damaged if mains is applied to the
terminals 21/22. Lines 21/22 max. 2 m whole length excl. modules. Bluetooth
network reset: (1) Power off device and disconnect from mains, apply short circuit
between LED+ and LED-, (2) connect device to mains and power on for at least
2 seconds, (3) power off device, disconnect from mains and remove short circuit.
Reset completed. Emergency Lighting: This LED power supply complies with
EN 61347-2-13 Annex J and is suitable for emergency lighting fixtures according
to EN 60598-2-22 except those used in high-risk task areas. The device can be
put into operation using the OSRAM HubSense Commissioning Tool version
1.30.1 (https://platform.hubsense.eu), subject to prior acceptance of the Terms
of Use and the Privacy Policy. OSRAM may terminate or suspend the use of the
HubSense Commissioning Tool at any time and for any or no reason in its sole
discretion, even if access and use is continued to be allowed to others. Compat-
ibility to future versions of the Hubsense Commissioning tool is not guaranteed.
The device complies with Bluetooth mesh Standard v1.0. It can also be used in
3rd party Bluetooth mesh network, that complies with this standard and that
supports the mesh models of this device, and with certain 3rd party commission-
ing tools, that support the mesh models of this device. In order to ensure correct
interoperability a verification with the 3rd party network components and the 3rd
2
Input / PRI
Output / SEC
Output / SEC
Cable types (tested acc. to EN 60598-1)
• NYM-J 3x1.5
• H05VV-F 3x1.5
• H05VV-F 2x1.5
• H05VV-F 2x1.0
• H05VV-F 2x1.5
• H05VV-F 2x1.0
• H03VV-F 2x0.75
• H03VV-F 2x0.5
• Style 21520
• H03VVH2-F 2x0.75
party commissioning tool is necessary in advance. Please contact OSRAM
(support@hubsense.eu) to receive the actual list of supported models for this
device. OSRAM shall have no liability for any 3rd party commissioning tool and
does not make any representations, express or implied, about the availability and/
or performance of such commissioning tool. OSRAM shall have no liability for and
does not make any representations, express or implied, about the connectivity of
OSRAM QBM products with any other products. Hereby OSRAM GmbH declares
that the radio equipment types OT Wi 15 NFC BL LP I, OT Wi 25 NFC BL LP I and
OT Wi 40 NFC BL LP I are in compliance with Directive 2014/ 53/ EU and the rel-
evant statutory instruments. The full text of the EU declaration of conformity or the
UK declaration of conformity is available at the following internet address:
www. osram. com/ot-indoor-ce. NFC frequency range: 13 553 – 13 567 kHz; Blue-
tooth frequency range: 2400 - 2483.5 MHz; Max HF output power (EIRP) of the
product: 8 dBm; Technical support: www.osram.com, +49 (0)89-6213-6000;
1) Qualified Bluetooth mesh compact LED driver for independent installation;
2) Constant current LED Power Supply; 3) wire preparation; push in; 4) t c point;
5) Made in Bulgaria; 6) picture only for reference, valid print on product; 7) Mains;
8) Input; 9) Output; 10) Year; 11) Week; 12) Safety note for mounting with metal
screw: The distance between the metal screw and the insulated single wires must
be at least 2.5 mm. 13) Mounting hint for proper radio connectivity. By integrating
the device into a casing the wireless range could be affected, in particular by
metal surfaces. Therefore, the wireless range needs to be verified after integration.
14) Do not place any mains voltage or LED supply wires within or close to this
area. 15) Recommended minimal distance to metal parts. 16) Placement of inte-
grated radio transmitter antenna; 17) Radio frequency; 18) Wireless protocol;
19) Qualified Bluetooth mesh; 20) Wireless range; 21) 10m line of sight; 22) Position;
23) Cable types (tested acc. to EN 60598-1); 24) A or B
23)
Werbung
