Accessories And Spare Parts; Scope Of Delivery; Warranty; Description Of The Device - Kärcher AF 20 Bedienungsanleitung

Electrical and electronic appliances contain valu-
able, recyclable materials and often components
such as batteries, rechargeable batteries or oil,
which - if handled or disposed of incorrectly - can
pose a potential threat to human health and the environ-
ment. However, these components are required for the
correct operation of the appliance. Appliances marked
by this symbol are not allowed to be disposed of togeth-
er with the household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found
at: www.kaercher.com/REACH

Accessories and spare parts

Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.

Scope of delivery

The scope of delivery for the appliance is shown on the
packaging. Check the contents for completeness when
unpacking. If any accessories are missing or in the
event of any shipping damage, please notify your deal-
er.

Warranty

The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Description of the device

For the illustrations, refer to the graphics page.
Illustration A
Operation button for Device On / Off
1
Operation button for Function lock
2
Display PM 2.5 Air quality index
3
Operation button for Switch off display
4
Display for fan level
5
Operation button for Auto mode On / Off
6
Fan level operation button
7
Operation button for Sleep mode On / Off
8
Timer display
9
Operation button for Timer
10
Filter service life display
11
Operation button for Filter reset
12
Air quality display and device display
13
Filter cover lock
14
Filter cover
15
Filter tab
16
filter
17
Connection for power supply unit
18
Device sensor
19
Power adapter
20
Note
The function settings are only possible via the operation
buttons and not via the displays.

Inserting the filter

Before initial start up, the fine filters already installed in
the unit must be unpacked.
1. Turn the device over, and turn the filter cover lock 45
degrees clockwise.
Illustration B
2. Remove the filter cover.
Illustration C
3. Remove the packed filters.
Illustration D
4. Unpack the filters.
Illustration E
5. Insert the unpacked filters. Ensure that the draw
shackles are visible and point inwards. Illustration
F
6. Put on the filter cover and turn the lock 45 degrees
anticlockwise. Turn the device over with the display
facing upwards.
Illustration G
7. Place the device on a level surface. Ensure that a
distance of 30 cm is maintained to each side.
Illustration H
Note
Do not place the device on hot surfaces or in the imme-
diate vicinity of the room heating.
Do not allow any liquids or foreign bodies (e.g. metallic
objects) to enter the device.
8. Insert the plug of the power supply unit into the de-
vice and insert the mains plug into the socket.
Illustration I
The device is ready for operation.
Note
The first time you use the device, we recommend allow-
ing it to run overnight to perform an initial basic cleaning
of your room.
Note
The table with the hours of the display symbols for the
filter service life, see Replacing the filter
Switching the device on/off
1. To switch on the device: Press the on/off button on
the device.
Illustration I
The device starts automatically.
Note
After the system is switched on, the displays and but-
tons on the control panel light up briefly. The integrated
air quality sensor measures the air quality in the room
automatically.
2. If required, the following functions, for example, can
be set via the operation buttons:
 Fan level
 Auto mode
 Sleep mode
 Timer
English

Operation

9