Black & Decker BHSM15FX08 Originalanweisungen Seite 10

ENGLISH
Attaching the floor extension to the floor
cleaning head (Fig. A)
Push the floor extension (7) into the floor cleaning head
u
(8) making sure it clicks securely into place, as shown in
figure A.
Attaching the hand held steam unit to the
floor extension (Fig. A1)
Push the hand held steam unit (3) firmly onto the
u
floor extension (7) making sure it sits correctly over the
interface and clicks securely into place.
Warning! Inspect the seal between the connection point
on the hand held steam unit (3) and the floor extrension (7)
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.
Removing the hand held steam unit
Push the release button (6) on the floor extension (7) and
u
lift the hand held steam unit (3) off the interface.
Attaching a cleaning pad (Fig. B)
Replacement cleaning pads are available from your
BLACK+DECKER dealer :- (cat no. FSMP20-XJ).
Place a cleaning pad (18) on the floor with the velcro 'loop'
u
side facing up.
Lightly press the steam mop down onto the cleaning pad.
u
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
Removing a cleaning pad
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop.
Do not wear slippers or open toed footwear.
Return the steam mop to the upright position and turn the
u
steam mop 'OFF'.
Wait until the steam mop cools down (approximately
u
minutes).
Lift the steam mop away from the cleaning pad (18)
u
freeing it from the velcro fastening by putting weight on the
cleaning pad removal tab (19).
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop supported in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Filling the water tank (Fig. C)
Note! Fill the water tank (5) with clean tap water (Do not use
any additives or chemicals).
Note! In areas of hard water, the use of de-ionised water is
recommended.
10
(Original instructions)
Open the filler cap (4) by flipping it up.
u
Fill the water tank (5) with water (Do not use any additives
u
or chemicals).
Warning! When filling, maintain the water tank (5) in vertical
position with the cap at the top.
Warning! Your water tank has a
fill the tank.
Close the filler cap (4).
u
Note! Ensure the filler cap is firmly secured.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pads fitted and a continuous run time
of 90 seconds.
Switching on and off (Fig. D)
To switch the appliance on, press the ON/Off switch (1).
u
It takes approximately 30 seconds for the boiler to
heat up. Once boiler is up to temperature the user must
press a steam setting to create steam.
To switch the appliance off, press the ON/Off switch (1).
u
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop supported in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
Floor Worktop Surface
Wood/Laminate
Tile/Vinyl
Stone/Marble
Accessories
Grout Brush
5
Small Brush
Small Brush with copper bristles
Window Squeegee
Garment Steamer
Steam user interface
This steam mop is fitted with an Steam user interface panel
(2) which shows two steam settings. They are used to select the
correct operating mode for your particular cleaning operation.
Turn unit on by pressing the On/Off switch (1).
u
Green LED starts flashing as boiler heats up.
u
Green LED stays solid once boiler is up to temp.
u
User must press either low or high steam button to create
u
steam.
0.5 litre capacity. Do not over
Setting
Low steam setting
High steam setting
High steam setting
Setting
High Steam setting
High Steam setting
High Steam setting
Low steam setting
Low steam setting