Technical Data; Brief Description - Felisatti PF102/1100VES Bedienungsanleitung

Planes
Absorbed power
No-load speed
Cutting depth
Total cut width
Rebate's depth
Approx. weight (without accessories)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at hand to
use when carrying out maintenance on the indicated parts.
If the tool is used with care and normal maintenance is carried
out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the
tool is strictly forbidden.
PLANER SAFETY RULES
Planer Safety Rules
- Wait for the cutter to stop before setting the tool down. An
exposed cutter may engage the surface leading to possible
loss of control and serious injury.
- Do not reach into the saw dust ejector with your hands.
They could be injured by rotating parts.
- Apply the machine to the workpiece only when switched on.
Otherwise there is danger of kickback when the cutting tool
jams in the workpiece.
- When working, always hold the planer in such a manner that
the planer base plate faces flat on the workpiece. Otherwise
the planer can become wedged and lead to injuries.
- Never plane over metal objects, nails or screws. The planer
blade and the blade shaft can become damaged and lead to
increased vibrations.
- Secure the workpiece. A workpiece clamped with clamping
devices or in a vice is held more secure than by hand.
- Never use the machine with a damaged cable.
Do not touch the damaged cable and pull the mains plug
when the cable is damaged while working. Damaged cables
increase the risk of an electric shock.
Products sold in GB only: Your product is fitted with an BS
16/A approved electric plug with internal fuse (ASTA
approved to BS 16).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 0 mA or less.
ILLUSTRATIONS
DESCRIPTION (See figures)
A Safety push button switch (Fig. 1)
B On-/off switch (Fig. 1)
D Support foot (Fig. )
E Drive wheel (Fig. 4)
F Toothed belt (Fig. 4)
G Idler pulley (Fig. 4)
H Vertical depth graduated scale (Fig. )

TECHNICAL DATA

PF82/710
W 650
/min 14000
mm 0-
mm 8
mm 15
Kg ,5
I Side end-stop immobilisation control (Fig. 1)
J Circular depth graduation scale (Fig. 1 and )
K Depth graduation handle (Fig. )
L Lateral stop (Fig. 1)
M Sawdust extraction (Fig. )
N Cope depth end-stop (Fig.)
O Blade replacement screws (Fig. )
P Guide slot (Fig. 1)
Q Toothed belt cover (Fig. 4)
R Toothed belt cover screw (Fig. 4)
S Mobile plate (Fig.  and )
T Dust suction adapter (Fig. 1)
U Base plate (Fig. 1 and )
V Side stop locking set square (Fig.1)
W Side stop regulation of the wing nut (Fig. 1)
Y Depth stop fixing wing nut (Fig. 2)
- Dust suction adapter
- Hexagonal key
- Lateral stop
- Depth end-stop
- Operating instructions
- Safety instructions
- Warranty
This tool has been designed to rout wood and similar
materials, to plane irregular surfaces and to cant off edges.
Before using the tool, make sure the mains voltage is correct:
it must be the same as that on the specification label.
Machines with 0V can also be connected to a 0-V mains
supply.
WARNING! Only plug in when machine is switched off.
Press the locking button A, and squeeze the trigger in the on/
off switch B. When the on/off switch is released, the machine
stops.
For safety reasons, it is not possible to lock On/Off switch
B, instead it has to be pressed while the machine is being
used.
CONSTANT ELECTRONICS (Mod. PF102/1100VES)
The built-in module permits:
- Soft start.
- The maintenance of a practically constant rated speed
up to rated power.
- An overload protection system by means of current
cut-off in the case of motor overload, in which case the
burring machine shuts down and re-starts when the grinding
pressure has been reduced.
PF102/1100VES
1100
11000
0-,5
EQUIPMENT

BRIEF DESCRIPTION

BEFORE USING THIS TOOL
START UP
10
15
,8