Operation; Technical Data - Felisatti PF180/1500 Bedienungsanleitung

Model:
Voltage
Frequency
Power input:
No load speed:
Planing depth:
Planing width:
Weight according EPTA-Procedure 01/2003
Read the operating instructions
Protection category II power tool; double
insulated
Wear eye protection
Follow very carefully the instructions in this manual,
save it and keep it close at hand, ready to carry out any
inspection of parts that may be necessary.
If the tool is used with care and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought
shall be only those described in this manual. Any other
use of the tool is strictly forbidden.
KNOW YOUR PRODUCT
Before using the power tool, familiarize yourself
with all the operating features and safety requirements.
Use the tool and accessories only for the applications
intended.
All other applications are expressly ruled out.
1. ON/OFF trigger switch
2. Lock-off button
3. Depth adjustment knob
4. Main handle
5. Front handle
6. Dust extraction port
7. Fence attachment knob (x 2)
8. Fence attachment point (x 4)
9. Reversible blades
10. Blade barrel
11. Clamping screw (x 5)
12. Movable front base
13. Fixed rear base
14. Combined parallel and bevel fence guide
15. Front handle lock lever
16. Front handle set screw
17. Drive belt cover
18. Dust extraction adaptеr
19. Blade spanner

OPERATION

This model FELISATTI power tool is supplied
from singlephase alternating current mains. It is double
insulated according to EN 60745, IEC 60745 and can be
connected to grounded or not grounded sockets. This
power tool is radio suppressed in compliance with EMC
Directive 2004/108/EC.

TECHNICAL DATA

V~
Hz
W
/min
mm
mm
kg
PRIOR TO INITIAL OPERATION
▪▪ Make sure power supply voltage corresponds to the
value indicated on the name plate with technical data
of the tool.
▪▪ Make sure the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
ADJUSTING THE FRONT HANDLE
1. Hinge out the front handle lock lever (15) and move
the front handle to one of the four positions to suit
best the intended task. (Fig. 1)
2. Hinge back the lever (15) to secure the front handle
in the selected position. (Fig. 2)
NOTE: If necessary the lever action mechanism can be
adjusted using the front handle set screw (16). (Fig.3)
ADJUSTING THE PLANING DEPTH
WARNING: Always ensure that the machine
is switched off and unplugged from the power
supply before making adjustments or before
installing or removing
blades.
(3) clockwise for a deeper cut and anti-clockwise for a
shallower cut. (Fig.4)
2. The numbers on the ring under the depth adjustment
knob indicate the depth of cut. For example when "2" is
next to the pointer on the front of the planer, the depth of
cut is 2 mm.
3. If it is necessary to plane to a precise depth, plane
a scrap piece of wood, measure the difference in thickness
and adjust the setting if necessary.
WARNING: Always ensure that the number
on the ring is at the "0" position when the tool
is not in use; at this position, the blade can
not cut the workpiece
REMOVING AND INSTALLING PLANER BLADES
WARNING: Always ensure that the tool is
switched off and unplugged from the power supply
before installing or removing blades.
Your planer is fitted with reversible blades. Blades can
be reversed when blunt. After both sides of the blades have
been used they should be discarded.
NOTE: These blades cannot be re-sharpened.
Removing a planer blade
WARNING: The blades are very sharp. Take
care when handling them.
1. Using the supplied spanner (19), loosen the five
clamping screws (11). (Fig.5)
2. Remove the planer blade (9) from the slot in the
blade barrel (10) in which it is retained. (Fig.6)
Installing a planer blade
1. Either turn over the planer blade (9) or replace it
PF180/1500
230
50-60
1500
15000
0–2
180
8,3
1. Rotate the depth adjustment knob
7