Noise/Vibration Information; Vacuum Mode - Bosch UniversalGardenTidy Originalbetriebsanleitung

Leaf blower/Garden Va-
cuum Cleaner
Weight (vacuum mode)
Protection class
Serial number
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

Noise emission values determined according to EN 50636-2-100.
Typically the A-weighted noise levels of the product are:
– Sound pressure level
– Sound power level
– Uncertainty K
Vibration total values a (triax vector sum) and uncertainty K determined according to EN 50636-2-100
h
– Vibration emission value a
h
– Uncertainty K
Blow Mode
Assembly (see figure B)
Before any work on the product, disconnect supply
u
cord from the mains.
Slide the nozzle (12) onto the motor unit. Take care not to
pinch your fingers during assembly.
Mount the safety cover (4) onto the motor unit. For this,
place the safety cover (4) into the hinge on the motor unit.
Position the safety cover (4) against the motor unit and
screw in fastening screw (3) until fully tight and clicks are
heard to secure the safety cover.
Operating (see figures C and D)
Make sure that the cable is not in your way while working.
To switch on, turn the On/Off switch (1) clockwise until it
clicks.
The airflow speed is variable. To increase the airflow speed,
turn the On/Off switch (1) clockwise.
To reduce the speed, turn the On/Off switch (1) anticlock-
wise.
To switch off, turn the On/Off switch (1) anticlockwise until
it clicks.
Set the On/Off switch (1) of the product to "0" before dis-
connecting the mains voltage or pulling the mains plug.
Disassembling (see figure E)
Before any work on the product, disconnect supply
u
cord from the mains.
Press button (11) in and remove the nozzle (12).
Loosen the fastening screw (3). Remove the safety cover (4)
and store it securely.
Bosch Power Tools
UniversalGardenTidy
kg 4.7
/ II

Vacuum Mode

dB(A)
dB(A)
dB
2
m/s
2
m/s
Vacuum Mode
Assembling (see figures F and G)
Before any work on the product, disconnect supply
u
cord from the mains.
Connect the three parts of the vacuum tube (7). Take care
not to pinch your fingers during assembly.
Mount the vacuum tube (7) onto the motor unit. Insert the
vacuum tube (7) into the hinge on the motor unit. Raise the
vacuum tube (7) to align the fastening screw with main hous-
ing, and screw in the fastening screw (3) until fully tight and
clicks are heard to secure the vacuum tube.
Mount the collection bag (10) to the motor unit and attach
the bag clips to the hooks on the vacuum tube. Take care not
to pinch your fingers during assembly.
Mounting the shoulder strap (see figure H)
Fasten the shoulder strap (9) with both hooks (8) to the
shoulder strap loops (13), Adjust the shoulder strap (9) so
that it comfortably carries the weight of the product and can
be guided easily.
Mounting and Adjusting the handle (see figures I
and J)
To attach the handle, place the handle (5) over the holders
on the tube, then insert the screw (6) though the handle and
tighten.
To adjust the angle, loosen the screw (6), move the handle
(5) up or down to the desired working position and then
tighten the screw (6) again.
UniversalGardenTidy UniversalGardenTidy
2300
4.7
/ II
see type plate on product
86
98
= 2.5
< 2.5
= 1.5
F 016 L94 484 | (20.07.2022)
English | 13
3000
4.7
/ II
Blow Mode
83
96
= 2.5
< 2.5
= 1.5