Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
You bought a technical device, the handling is easy and sim-
ple, but requires the observance of certain precautions. We
therefore ask you to read the following instructions carefully!
For the operation of the filter system, you need a skimmer (sur-
face skimmer). Either an integrated skimmer (built into the pool
wall) or a suspended skimmer (attachment to the poolwall).
Positioning
The installation area you set between the skimmer and the
inlet noz-zle so, that there is an adequate safety margin
to the pelvic wall. We recommend putting the filter system
in addition on base plates (for example: washed concrete
slabs etc.). These have to be installed with the spirit level.
Under no circumstances you may put your filter system in a
trough or directly into the grass (flood danger or risk of over-
heating of the filter pump).
If
you
have
sunk
your
ly, so it makes sense to place the filter pump in a fil-
ter slot, which should connect directly to the pelvis.
Is your filter pump housed in a filter slot, so it has to be in-
sured, that the filter slot can't be slooded. For this pur-
pose you should bring in a roller-burnishing (crushed
rock) in the range of the filter slot, so that the surround-
ing- and rainwater can seep away. It would be ideal if there
is a direct connection to the drain in the sump of the fil-
ter shaft (or sludge pump, with automatic floating switch).
It is important to ensure that the filter slot should never be air-
tight, because this may cause damage, due to condensation
water, on the filter pump. The size of the filter shaft should be
selected so that work can be performed on the filter system.
The necessary accessories such as hoses, hose clamps and
filter sand (not included) are offered gladly from your pool deal-
er.
Assembly of the filter system (Illustration 1)
Assemble the filter system at the location where the pump
finally will be (the subsequent transport there would be too
burdensome!).
The filter pump consists of the following parts:
1.
Pump
2.
valve
3.
Seal (O-Ring)
4.
clamping ring
5.
vessel
6.
Central pipe
7.
Filter screen
8.
Drain plug
9.
Centralizer (cover for standpipe)
10.
Base plate
11.
Pressure hose
Filter vessel
Insert stand pipe including filter screen into boiler (Figure 2)
2.
Place the stand pipe with the filter screen on the floor
of the boiler, make sure that the stand pipe is located in the
middle of the boiler and that the drain plug is screwed in.
3.
Now put the centralizer on the tank opening, while
centering the standpipe. (Illustration 4)
4.
Fill in the filter quarz sand up to a high of about ¾ of
the bowlhight.(right grit 0,6mm - 1,2mm, Quantity: depending
on filter size) (Illus-tration 4)
8
pool
partially
or
complete-
5.
Then mount the top oft he boiler or the valve head
and the boiler seal on the tank top of the filter vessel. Before
you do this, it is neccassary to clean again and wash off any
sand or accumulated debris. The connection of the top of the
boiler or the head valve with the filter vessel is carried out
by the clamping ring. The clamp-ing ring is screwed with the
clamping ring screw and the collet nut.(Illustration 5 & 6)
6.
Finally, mount the pump fittings on the valve head.
Seal the pump fittings sufficiently by using teflon tape.
7.
The pressure gauge (if included) is screwed to the
side of the 7-way valve and sealed. The existing vent plug
should be removed first. Illustration 9
Pump hose connections (Illustration 7)
1.
Skimmers: Connection from skimmer to the front
connector of the filter pump.
2.
Pressure line: Connection going from the upper
area of the top of the filter pump to the connector with the
designation "PUMP" at the
7-
way valve.
3.
Return line: Connection from the 7-way valve with
the designation "RETURN" to the connection at the inlet
nozzle (pool). Secure all connections with hose clamps.
4.
Backwash: Connection „WASTE" (Empty) in the
channel. Con-nections are made with special pool hoses and
hose clamps!
Commissioning of the filter system
1.
Before you go in operation with the filter system, it
must be insured that the filter system stands outside the basin
and in the level low-er than the water level of the pool is, and
the hose connections are properly connected and secured.
2.
The swimming pool must be filled with water, accord-
ing to the in-structions of your pool dealer. The water must flow
towards the fil-ter pump. Now the filter pump is vented. If avail-
able, open slightly the preliminary filter of the filter pump until
water flows from the prefilter top. (transparent cover with screw
connection on the top of the filter pump) For non self-priming
pumps, it is neccassary that the water level is above the filter
pump.
3.
Place the handle on the 7- way valve to the Back-
wash position. Only now the filter pump is taken in operation.
Backwashing about 2 - 3 minutes to perform. Then turn the fil-
ter pump off again and put the handle on the valve head in the
RINSE position. Rinsing for 30 seconds. Thereafter, the filter
pump is switched off again and the handle set to the position
FILTER. The backwashing and rinse water you best pipe in
the channel.
4.
Turn the filter pump back on. The filter system is in
normal filter operation. We recommend a filter run time of 2 x
4 - 5 hours per day. If you clean the bottom of your pool with a
pool vacuum cleaner, this is also done in the position filter. Af-
ter each floor-cleaning or when the pressure on the pressure
gauge if available (by 2 - 3 ticks) rises, backwashing is required.
5.
After BACKWASHING always a REFLUSHING with
a duration of approximately 30 seconds is required. This caus-
es the reduction of the sand in the filter vessel.
6.
If you clean your pool with a pool vacuum cleaner,
this can also be done with the 7-way valve in the position
DRAINING to remove impurities from the pool (eg: algae),
which otherwise go back through the filter sand. In doing so,
the water which is extracted from the ground, will be directly
pumped through the backwash line into the open air. After this
process, the water level of the pool is supplemented accord-
ingly.
Werbung
