Use / Operating The Torque Wrench With Built-In Angle Gauge; Accessories; Maintenance And Care - Hazet-Werk 7292-eTAC Betriebsanleitung

8 . 2 Rotation angle
The "Nm / °" menu option also enables you to perform
the programming for the screw tightening process using
"Rotation angle".
1. After selecting in the "Nm / °" menu option, you can
set the joint torque value using
2. After confirming the value using
value for the rotation angle using
changes in 5° steps.
3. After confirming this value using
defined the joint torque and the rotation angle values.
ATTENTION! "Rotation angle" mode is only active
when the rotation angle is set to a value greater
than 0°.
NOTE! The signals of the torque wrench with
built-in angle gauge give the user not only the
numeric values on the display, but also the
applied torque wrench as well as the applied
rotation angle.
8 . 3 Use / operating the torque wrench
with built-in angle gauge:
The torque wrench with built-in angle gauge should only
be operated with the handle at right angles to the screw
joint. The hand force deployed must be applied uniformly
onto the centre of the handle (ring marking).
In order to avoid measurement errors when measuring the
rotation angle, the work piece to be screwed or its support
should not rotate, move or shake during the operation.
9 . Adjustment / calibration:
An electronic torque wrench with built-in angle gauge
should be checked and calibrated regularly. After a long
period of use, re-certification or re-calibration by the
factory is advisable. Electronic torque wrenches with
built-in angle gauges are measurement tools. Appropriate
measurement equipment must be used to test (and where
applicable, adjust) measurement tools at the time intervals
laid down by Quality Management.
The interval between test dates is dependent on the
frequency of use. We recommend testing after ca. 5000
screw operations, but no later than 6 months.
NOTE! The "PC" menu option provides infor-
mation on the software version, the serial num-
ber, the date of the last calibration, and the
remaining number of operations until the next
calibration of the wrench.
1. In order to call up information under the "PC" menu
item, you will need to switch to the menu using
and preferably select the "PC" menu option using
2. After confirming using
you will then be able to see information on the soft-
ware version.
HAZET has the corresponding torque testers. After
testing and any adjustments required, HAZET torque
3 Design and Function
All manuals and user guides at all-guides.com
.
, you can set the
. The setting
, you will have
in the "PC" menu option,
wrenches with built-in angle gauge and torque test-
ers sent to HAZET are supplied with a test certificate.
The HAZET torque and rotation angle testing devices
are constantly supervised by the German Calibration
Service (DKD), and calibrated and/or adjusted as
required. This guarantees the level of expertise neces-
sary for the field of controlled screw joint tightening -
and the quality of your HAZET tool.
We can also retrieve the electronic torque wrench with
built-in angle gauge via your specialist retailer for check-
ing and calibration at the HAZET plant.
10 . Torque and Rotation Angle Certificate
and Calibration Document
Every torque wrench with built-in angle gauge is pro-
vided with a quality test certificate in accordance with
DIN 55350-18-4.2.2.
Should you lose the certificate or if you are required to
do so in the calibration documents, please get in touch
with the HAZET Service Centre.

11 . Accessories:

All HAZET torque wrenches with built-in angle gauges can
be provided with a wide range of quality accessories. Find
out more in your HAZET tool manual or on the Internet at:
www.hazet.de or www.hazet.com

12 . Maintenance and care:

None of the internal mechanical and electronic func-
tional elements require any maintenance.
.
23