Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1 . General Aspects
CAUTION! Specialist technical knowledge and/
or suitable training is required for the use and
repair of this tool.
This device was developed and manufactured accord-
ing to the technical norms and standards valid at the
time and is considered to be operationally reliable.
Nevertheless, the tool set can present a danger when
it is not used as intended or in an inappropriate way by
non-qualified personnel. All persons using or maintain-
ing this tool must carefully read and understand these
operating instructions before commencing work.
2 . Owner's Liability
• Keep the operating instructions together with the tool
at all times. If the operating instructions have been
mislaid or made unusable, please contact your spe-
cialist dealer or the HAZET Service Centre.
• Before each use, check the torque wrench with built-
in angle gauge for full functionality. Do not use the
tool if its functional efficiency cannot be ensured or if
damage is detected. If the tool is used when it is not
in full working order, there is a risk of severe personal
injury and property damage.
• The torque wrench with built-in angle gauge must
only be used if it is in good working condition. If the
device does not work properly, it must be removed
from service and inspected.
• All safety warning and operating instructions on the
device must be observed, and always be in an easily-
legible condition. Damaged descriptions, labels or
stickers as well as the display cover must be imme-
diately replaced.
• In addition to the occupational safety advice given
in these operating instructions, the general safety
regulations, regulations for the prevention of acci-
dents and regulations for environmental protection
applicable for the use of this tool must be observed
and respected.
• All safety equipment must always be within reach and
should be checked regularly.
• Familiarise yourself with the operation of the torque
wrench with built-in angle gauge and undergo train-
ing for working with the tool before starting work.
Before use, carefully check that all programmed set-
tings are correct. The quality of your screwing work
will be dependent on these settings.
16
All manuals and user guides at all-guides.com
2
For Your Safety
3 . Intended use
• Operational reliability can only be ensured if the tool
is used as intended and in compliance with the indi-
cations given in the operating instructions. Any devia-
tion from the intended use and/or any misapplication
of the device is prohibited and will be considered as
improper use.
• Ensure that tools are always used, inspected and main-
tained in compliance with the respective local, state,
national or federal regulations.
• HAZET torque wrenches with built-in angle gauge are
solely designed to enable the controlled tightening
and loosening of screw connectors.
• The wrench should under no circumstances be used
as a lever tool, clamping tool or impact tool. Improper
use, use which is not compliant with the safety
instructions or overloading of the HAZET torque/
rotation angle wrench can lead to incorrect measure-
ments and/or to a failure of the system, and thus to
death, severe damage to your body or health, as well
as to property.
• Torque wrenches with built-in angle gauge are cali-
brated measurement tools and as such must be
treated with care. For this reason mechanical, chemi-
cal or thermal impacts which go beyond the capa-
bilities of its intended use should be avoided. The
torque wrench with built-in angle gauge must not be
exposed to rain or humidity, or immersed in a liquid.
Do not allow foreign bodies to enter, and always
cover the sockets when not in use. Extreme climatic
conditions such as cold, heat, humidity can affect
the measurement values or affect the measurement
results. Non-compliance can damage or destroy the
torque wrench with built-in angle gauge.
• Incorrect use of the contained tool or use whilst fail-
ing to comply with the safety instructions can result
in serious injury.
• Any deviation from the intended use and/or any
misapplication of the tool is prohibited and will be
considered as improper use.
• Before use, check that the insert used and/or the
plug tool are/is seated firmly. Position the tool so
that it cannot slip out from the screw connection.
Otherwise, there is a risk of personal injury and/or
property damage.
• When using inserts or plug tools, it is vital to ensure
their design conforms to standards and that their
shape and size are correct for the screw joint to be
tightened.
• Also adhere to the maximum permitted load for the
insert or plug tool used. These may be lower than
the possible release torque of the torque wrench with
built-in angle gauge. The use of home-made special-
ised tools can be a source of danger. Failure to comply
can result in personal injury and/or material damage.
Werbung
Inhaltsverzeichnis
