Accessories - Black & Decker CD71CRE Bedienungsanleitung

• Rotate the side handle into the desired position.
• Insert the depth stop (6) into the mounting hole
as shown.
• Set the drilling depth as described below.
• Tighten the side handle by turning the grip
clockwise.
Fitting a drill bit or screwdriver bit
Keyless chuck (fi g. B)
• Open the chuck by turning the front part (8) with
one hand while holding the rear part (9) with the
other.
• Insert the bit shaft (10) into the chuck and fi rmly
tighten the chuck.
Keyed chuck (fi g. C)
• Open the chuck by turning the sleeve (11) coun-
terclockwise.
• Insert the bit shaft (10) into the chuck.
• Insert the chuck key (12) into each hole (13) in
the side of the chuck and turn clockwise until
tight.
Removing and refi tting the chuck (fi g. D)
• Open the chuck as far as possible.
• Remove the chuck retaining screw, located
in the chuck, by turning it clockwise using
a screwdriver.
• Tighten an Allen key into the chuck and strike it
with a hammer as shown.
• Remove the Allen key.
• Remove the chuck by turning it counterclock-
wise.
• To refi t the chuck, screw it onto the spindle and
secure it with the chuck retaining screw.
Use
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, fl oors or ceil-
ings, check for the location of wiring and pipes.
Selecting the direction of rotation (fi g. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or
removing a jammed drill bit, use reverse (counter-
clockwise) rotation.
• To select forward rotation, push the forward/re-
verse slider (3) to the centre position.
• To select reverse rotation, push the forward/re-
verse slider to the left.
Warning! Never change the direction of rotation
while the motor is running.
Selecting the drilling mode
• For drilling in masonry, set the drilling mode
selector (4) to the position.
• For drilling in other materials and for screw-
driving, set the drilling mode selector to the
position.
All manuals and user guides at all-guides.com
Setting the drilling depth (fi g. F)
•
•
•
Switching on and off
•
•
•

Accessories

The performance of your tool depends on the
accessory used. Black & Decker and Piranha ac-
cessories are engineered to high quality standards
and designed to enhance the performance of your
tool. By using these accessories you will get the
very best from your tool.
Maintenance
Your tool has been designed to operate over a long
period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance,
switch off and unplug the tool.
•
•
Mains plug replacement
(U.K. & Ireland only)
If a new mains plug needs to be fi tted:
•
•
•
Warning! No connection is to be made to the earth
terminal. Follow the fi tting instructions supplied
with good quality plugs. Recommended fuse: 5 A.
5
Slacken the side handle (7) by turning the grip
counterclockwise.
Set the depth stop (6) to the desired position.
The maximum drilling depth is equal to the
distance between the tip of the drill bit and the
front end of the depth stop.
Tighten the side handle by turning the grip
clockwise.
To switch the tool on, press the variable speed
switch (1). The tool speed depends on how far
you press the switch. As a general rule, use
low speeds for large diameter drill bits and high
speeds for smaller diameter drill bits.
For continuous operation, press the lock-on
button (2) and release the variable speed
switch. This option is available only at full
speed. This option does not work in reverse
rotation.
To switch the tool off, release the variable
speed switch. To switch the tool off when in
continuous operation, press the variable speed
switch once more and release it.
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the motor housing using
a damp cloth. Do not use any abrasive or sol-
vent-based cleaner.
Safely dispose of the old plug.
Connect the brown lead to the live terminal in
the new plug.
Connect the blue lead to the neutral terminal.
ENGLISH