Cleaning And Maintenance - UNIPRODO UNI AIR PURIFIER 01 Bedienungsanleitung

EN
d) Only the manufacturer's service point may
repair the device. Do not attempt any repairs
independently!
e) In case of fire, use a powder or carbon dioxide
(CO ) fire extinguisher (one intended for use on
2
live electrical devices) to put it out.
f) Please keep this manual available for future
reference. If this device is passed on to a third
party, the manual must be passed on with it.
g) Keep packaging elements and small assembly
parts in a place not available to children.
h) Keep the device away from children and animals.
i) If this device is used together with another
equipment, the remaining instructions for use
shall also be followed.
2.3. PERSONAL SAFETY
a) To prevent the device from accidentally switching
on, make sure the switch is on the OFF position
before connecting to a power source.
b) The device is not a toy. Children must be
supervised to ensure that they do not play with
the device.
c) The device is not designed to be handled by
persons (including children) with limited mental
and sensory functions or persons lacking relevant
experience and/or knowledge unless they are
supervised by a person responsible for their
safety or they have received instruction on how to
operate the device.
2.4. SAFE DEVICE USE
a) Do not use the device if the ON/OFF switch does
not function properly (does not switch the device
on and off). Devices which cannot be switched on
and off using the ON/OFF switch are hazardous,
should not be operated and must be repaired.
b) Make sure the plug is disconnected from the
socket before attempting any adjustments,
accessory replacements or before putting the
device aside. Such precautions will reduce the risk
of accidentally activating the device.
c) When not in use, store in a safe place, away from
children and people not familiar with the device
who have not read the user manual. The device
may pose a hazard in the hands of inexperienced
users.
d) Keep the device in perfect technical condition.
Before each use check for general damage and
especially check for cracked parts or elements
and for any other conditions which may impact
the safe operation of the device. If damage is
discovered, hand over the device for repair before
use.
e) Keep the device out of the reach of children.
f) Device repair or maintenance should be carried
out by qualified persons, only using original spare
parts. This will ensure safe use.
g) To ensure the operational integrity of the device,
do not remove factory-fitted guards and do not
loosen any screws.
h) Do not touch articulated parts or accessories
unless the device has been disconnected from the
power source.
i) Clean the device regularly to prevent stubborn
grime from accumulating.
8
j) Do not cover the air intake and outlet.
k) The device is not a toy. Cleaning and maintenance
may not be carried out by children without
supervision by an adult person.
l) It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
m) Keep the device away from sources of fire and
heat.
ATTENTION! Despite the safe design of the
device and its protective features, and despite
the use of additional elements protecting the
operator, there is still a slight risk of accident or
injury when using the device. Stay alert and use
common sense when using the device.
3. USE GUIDELINES
The device is designed to clean the air (of dust, pollen,
smoke) indoors. The product is intended for home use
only!
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
1
2
5
3
4
6
1. Air outlet
2. Control panel
3. LED backlight
4. Air inlet
5. Replaceable filter (inside the device)
6. Base
Control panel
1
2
3
4
1. Power button
2. Button for selecting the blowing power
(L - low, M - medium, H - high)
3. Timer button (2/4/8-hours)
4. Button to select LED backlight
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher
than 40°C and the relative humidity should be less
than 85%. Ensure good ventilation in the room in which
the device is being used. There should be at least 10
cm distance between each side of the device and the
wall or other objects. Keep the device away from any
hot surfaces The device should always be used when
positioned on an even, stable, clean, fireproof and dry
surface, and be out of the reach of children and persons
with limited mental and sensory functions. Position the
device such that you always have access to the power
plug. The power cord connected to the appliance must
be properly grounded and correspond to the technical
details on the product label.
ASSEMBLING THE APPLIANCE
CAUTION: Before using for the first time, remove the
filter from the device and the protective packaging, then
put it back in the device.
The device should be disconnected from the power
source! Turn the device upside down and remove its
base by turning it using the handle towards „OPEN".
Then remove the base and the filter. The filter is
installed in the reverse order, and the base must be
tightened as far as it will go towards „CLOSE".
1 2
4 5
CAUTION: the same procedure applies when replacing
a used filter with a new one.
3.3. DEVICE USE
CAUTION: connect the adapter to the device and then
connect it to the power source. The device should start
a short acoustic signal and all the lights on the control
panel will light up in blue and go out after 1 second. The
device will switch to standby mode.
A. Turning the device on/off
After confirming that the device has been
connected to a power source, press the power
button (1) on the control panel. A short acoustic
signal will sound, and the power button (1), low
blowing and LED backlight indicators will light up
and the device will work with the default settings.
To turn off the device, press the power button (1)
on the control panel again - a short acoustic signal
will sound, and then all the lights and backlight
will go out.
9 EN
B. Setting the timer
During the operation of the device, you can set
the time after which it switches itself off. To do
this, hold the timer button (3) on the control
panel until the indicator light for the desired time
(2/4/8-hours) lights up and a short beep sounds.
After the required time has elapsed, the lights and
backlight turn off and the device turns off.
C. Choice of LED backlight
In standby mode, when you press the LED
backlight selection button (4) on the control panel,
it will turn off. Pressing the same button (4) again
will turn on the LED backlight in the „muffled"
mode (eg. when working at night) and a short
acoustic signal will sound. Another pressing of
the LED backlight button (4) will cause a short
acoustic signal and the device backlight will switch
to normal mode. Another pressing of the LED
backlight button (4) will turn it off again, etc.
D. Choosing blowing power
When the device is turned on, press (an acoustic
sound will sound) on the control panel the
button for selecting the blowing power (2) and
hold it until the indicator of the desired power is
backlighted: L - low, M - medium, H - large and
repeat according to this pattern.
E. Signaling of used filter
If the LED backlight (3) starts blinking red it means
that the air filter should be replaced. The filter
3
replacement procedure is described in section 3.2.
CAUTION: after replacing the filter with the new
one with device switched on, press and hold
the power button for 7 seconds to cancel the
red backlight signaling the need to replace the
filter. The device has a built-in hour meter - a red
blinking backlight indicating the need to replace
the filter lights up after 2,200 operating hours.

3.4. CLEANING AND MAINTENANCE

a) Unplug the mains plug and allow the device to
cool completely before each cleaning, adjustment
or replacement of accessories, or if the device is
not being used. Wait for the rotating elements to
stop.
b) Always unplug the device before cleaning it.
c) Store the unit in a dry, cool place, free from
moisture and direct exposure to sunlight.
d) Do not spray the device with a water jet or
submerge it in water.
e) Do not allow water to get inside the device
through vents in the housing of the device.
f) Clean the vents with a brush.
g) The device must be regularly inspected to check
its technical efficiency and spot any damage.
h) Use a soft cloth for cleaning.
i) Do not use sharp and/or metal objects for
cleaning (e.g. a wire brush or a metal spatula)
because they may damage the surface material of
the appliance.
j) Do not clean the device with an acidic substance,
agents of medical purposes, thinners, fuel, oils
or other chemical substances because it may
damage the device.
k) Wipe the device regularly with a dry, soft cloth,
especially the ventilation openings and dust
accumulated on the filter.