Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Digital calliper COXT710351
Operating and safety instructions
Intended use
For private use only. Not for commercial use.
Package contents
1 x digital calliper gauge
1 x battery 1.5 V LR44
Part description
1. Graduated measure-
7.
Adjusting wheel for measuring
ment surfaces
jaws
2. Inner measuring jaws
8.
Battery compartment cover
3. Inch/mm key
9.
Button for zeroing (ZERO)
4. Locking screw
10. ON/OFF button (ON/ OFF)
5. LCD display
11. Outer measuring jaws
6. Depth measuring
blade
Technical data
Unit of measurement: mm, inch
Measuring range: 0 - 150 mm/ 0 - 6"
Resolution: 0.01 mm / 0.0005"
Accuracy: 0 - 200 mm/ 0 - 8" ± 0.03 mm/ 0.001"
Maximum measuring speed: 1.5 m/s, 60"/s
Measuring system: contactless, linear CAP measuring system
Safety instructions
Please read the operating instructions before use! Please keep the operating instructions in a safe place!
Caution! Risk of injury!
• The product should not be used by children. This product is not a toy!
• Never leave children unsupervised with the packaging material. There is a risk of suffocation.
Danger of death!
Batteries can be swallowed, which can be life-threatening. Seek medical attention immediately if a battery is swallowed.
• Never expose the product to high temperatures and humidity, otherwise the product may be damaged.
• Do not put the calliper under tension. Otherwise, the chip in the calliper may be damaged.
• Keep the calliper clean and dry. Liquid can damage the calliper.
Safety instructions for batteries
Caution! Danger of explosion!
• Never recharge batteries!
• Remove a depleted battery from the product immediately. There is an increased risk of leakage!
• Pay attention to the correct polarity (+ and -) and use only the specified battery type.
• Wear protective gloves! Leaking or damaged batteries can cause burns if they come into contact with the skin.
• Avoid contact with skin, eyes and mucous membranes. In case of contact with battery acid, rinse the affected area with plenty
of water and/or consult a doctor!
Warning! Turn the product OFF before inserting the battery (LCD display
• Remove the battery from the unit if it will not be used for an extended period.
• Do not short-circuit the connection poles under any circumstances.
Before commissioning
1. Insert / replace battery
Note: Low battery warning by flashing indicator.
• Slide open the battery compartment cover
and remove the old battery.
8
• Insert a new battery into the battery compartment, observing the polarity (+ and -). Make sure that the positive pole is facing
outwards and push the battery compartment cover
2. Prepare calliper gauge
• Loosen the locking screw
so that you can move the calliper.
4
• Clean all measuring surfaces and the calliper bar with a dry cotton cloth. Otherwise, incorrect measurement results may
occur, for example due to humidity.
• Check all buttons, switches and the LCD display
1 x storage box
1 x instruction manual
1
2
3
4
5
mm/inch
mm
OFF
ON
ZERO
11
10
9
8
7
Display: LCD display
Operating temperature: 0°C ~ +40°C
Influence due to humidity: insignificant within 0% to
80% relative humidity
Battery: 1.5 V LR44 (included in delivery)
is off).
5
shut again.
8
for proper reactions.
5
Putting the device into operation
1. Use calliper gauge
• Loosen the locking screw
by turning it anticlockwise.
4
• Push the outer measuring jaws
11
• Turn on the LCD display
by pressing the ON / OFF button
5
• Press the inch/mm button
to set the unit of measurement (inch or mm) you want to use. Either „mm" or „inch" appears in
3
the LCD display
5
.
• Press the zeroing (ZERO) button
9
Measuring the object from the outside:
• Push the outer measuring jaws
11
6
jaws
on the object to be measured.
11
Measuring the object from the inside:
• Place the inner measuring jaws
2
• Turn the adjusting wheel
anticlockwise outwards. Push the inner measuring jaws
7
both inner sides. Be careful not to damage the object to be measured by applying too much pressure.
Measuring the depth of an object:
• Slide the depth gauge blade
out of the calliper.
6
• Place the depth measuring blade
6
• Slide the body of the calliper down until you feel resistance.
• Be careful not to damage the depth measuring blade
• The LCD display
now shows the measurements.
5
• After taking the measurement, push the outer measuring jaws
adjusting wheel
clockwise inwards.
7
• Switch the LCD display
off again by pressing the ON / OFF button
5
Note: After approx. 5 minutes, the LCD display
• Tighten the locking screw
again by turning it clockwise until you feel resistance.
4
2. Troubleshooting
The unit contains sensitive electronic components. Therefore, it is possible that it may be disturbed by radio transmitting equipment
in the immediate vicinity. If faulty indications appear in the display, remove such devices from the vicinity of the unit.
Electrostatic discharges can lead to malfunctions.
• In case of such malfunctions, remove the battery for a short time and reinsert it.
Problem:
Every second, 5 digits jump simultaneously.
The LCD display
does not continue counting.
5
No display on the LCD screen.
Maintenance and cleaning
• Always keep the calliper clean and dry.
• Clean with a dry cotton cloth. Do not use solvents.
• Switch off the display when not in use to save battery power. When not in use for a long time, remove the battery and store it
separately.
Disposal
When your device has reached the end of its service life, do not throw it in the household rubbish, but dispose of it properly.
Defective or used batteries must be recycled in accordance with Directive 2006/66/EC. Return batteries and/or the appliance via the
collection facilities provided.
You can find the declaration of conformity on our website www.conmetallmeister.de
Conmetall Meister GmbH · Hafenstraße 26 · 29223 Celle · GERMANY · www.conmetallmeister.de
/inner measuring jaws
together.
2
.
10
to reset the LCD display
to zero.
5
apart by turning the adjusting wheel
anticlockwise outwards. Place the outer measuring
7
from the inside against the object to be measured.
2
against the object to be measured until it touches the surface (e.g. inside a hole).
or the object to be measured by applying too much pressure.
6
/ inner measuring jaws
11
.
10
switches off automatically.
5
Solution:
The battery voltage is below 1.45 V. Remove cover and replace
battery.
Faulty circuit. Replace battery, put it back in the compartment
after 30 sec.
1. Poor battery contact. Check battery compartment, clean if
necessary.
2. Battery voltage is below 1.3 V. Replace the battery with the
correct battery.
apart until they touch the object on
back together by turning the
2
Werbung
Inhaltsverzeichnis
