Sharp HT-SB100 Bedienungsanleitung Seite 6

5
Accessories
• Remote control (inc. batteries)
• Power cable
• Wall mount brackets
• Wall mount fixings (screws and plugs)
• Silicone rubber feet
• User documentation
Controls
(Refer to 1 on page 1).
1. button
Switch the unit between ON and STANDBY mode.
2. button
Select the source of audio (e.g. HDMI, USB, optical, etc)
3. button
Select Bluetooth mode. Press and hold to activate the
pairing function in Bluetooth mode or disconnect
the existing paired Bluetooth device.
4. button
Mute or resume the sound.
5. +/– buttons
Increase/decrease the volume level.
6. Remote Control Sensor
7. LED Indicator
Red: STANDBY
Green: AUX
Blue: Bluetooth
Yellow: Optical
Cyan: HDMI ARC
Purple: USB
8. Wall bracket screws
Inputs/outputs
(Refer to 2 on page 1).
1. OPTICAL
Opticial input jack.
2. HDMI ARC
Connect to a TV via HDMI cable (HDMI version 1.4 or higher).
3. USB
Insert USB flash drive to play music.
4. AUX
Connect to an external audio device.
5. AC~
Connect power cord.
Remote control
(Refer to 3 on page 1).
1. Switch the unit between ON and STANDBY mode.
2.
Select Bluetooth mode.
Press and hold to activate the pairing function in Bluetooth mode
or disconnect the existing paired Bluetooth device.
3. Press repeatedly to select a signal source AUX, BT (Bluetooth),
OPT (Optical), ARC (HDMI) and USB mode.
4. +/– Increase/decrease the volume level.
5. / Skip to previous/next track in Bluetooth or USB mode.
6.
Play/pause/resume playback in Bluetooth or USB mode.
7.
Mute or resume the sound.
8. BASS +/– Adjust bass level. This only changes CUST EQ settings.
9. TRE +/– Adjust treble level. This only changes CUST EQ settings.
10. EQ Press repeatedly to switch between movie, music, voice, and
custom equaliser modes.
Remote control operation
The provided remote control allows the unit to be operated from a
distance.
• Even if the remote control is operated within the effective range
of 6m, remote control operation may be impossible if there are
obstacles between the unit and the remote control.
• If the remote control is operated near other products which
generate infrared rays, or if other remote control devices using
infra-red rays are used near the unit, it may operate incorrectly.
Conversely, the other products may operate incorrectly.
Battery installation
(Refer to 4 on page 1).
1. Press the battery compartment cover release clip in the direction
of the arrow and then pull the cover away from the remote.
2. Insert two AAA size batteries (included). Make sure the (+) and (–)
ends of the batteries match the (+) and (–) ends indicated in the
battery compartment.
3. Close the battery compartment cover ensuring the release clip is
secured.
First time installation
Placement and mounting
(Refer to 5 on page 1).
A: Normal placement (place Soundbar on level surface in front of the
TV). Attach the silicone feet to the bottom of the soundbar.
B: Wall mounting
Wall mounting
NOTE:
ū Installation must be carried out by qualified personnel only.
Incorrect assembly can result in severe personal injury and property
damage (if you intend to install this product yourself, you must
check for installations such as electrical wiring and plumbing that
may be buried inside the wall). It is the installer's responsibility to
verify that the wall will safely support the total load of the unit and
wall brackets.
ū Additional tools (not included) are required for the installation.
ū Do not overtighten screws.
ū Keep this instruction manual for future reference.
ū Use an electronic stud finder to check the wall type before drilling
and mounting.
(Refer to 6 on page 1).
1. Drill 4 parallel holes (Ø 5.5~6 mm each according to wall type) in
the wall. The distance between the holes should be 708 mm.
Firmly fix 1 plug into each hole in the wall.
2. Tighten the wall mount brackets on the wall with screws and
screwdriver (not included). Make sure the they are securely
installed.
3. Loosen the screws at the back of the unit for 2~3 mm.
4. Lift the unit onto the wall mount brackets and slot into place.
Connections
HDMI ARC input
(Refer to 7 on page 2).
The ARC (Audio Return Channel) function allows you to send audio
from your ARC- compliant TV to your sound bar through a single HDMI
connection. To enjoy the ARC function, please ensure your TV is both
HDMI-CEC and ARC compliant and set up accordingly. When correctly
set up, you can use your TV remote control to adjust the volume
output (+/– and ) of the sound bar.