Noise And Vibration; Maintenance And Care; Warranty; Declaration Of Conformity - Felisatti RF55/1000E Bedienungsanleitung

Dust extraction keeps the workplace clean, prevents
dust build-up in the air and facilitates waste elimination.
These milling machines are fitted with adapter, which
can be coupled to a universal vacuum aspirator or other
dust suction device.
CAUTION: A suction extractor should always be used
that has been designed in accordance with the applica-
ble directives in relation to dust emission when milling
wood. The flexible hoses of conventional vacuum clean-
ers fit directly onto the dust extraction nozzle.
Installing the dust suction adapter
PRECAUTION: Before installing the suction adapter K,
press the fixing lever H so that the upper section of the
machine ascends to the upper position.
In order to install the dust suction adapter K, it
should be inserted in the square opening on the base
plate P until it fits fully into place, and then fixed
using the wing screws R, which are located on both
sides of the adapter K.
In order to maintain optimum chip extraction, the suction
adapter K should be periodically cleaned.
The aspirator should be suitable for the material being
worked.
A special aspirator must be employed in those cases
where dry harmful or carcinogenic dust is produced.
In situations where prolonged wood operations are
performed or machines are used industrially with
materials that produce dust that is harmful to health,
the machine must be connected to a suitable external
aspiration device.

NOISE AND VIBRATION

This tool has been designed and made to reduce noise
to a minimum. However, in spite of this, in certain
circumstances the maximum noise level in the place
of work could exceed 85 dBA. In this case, the op-
erator should wear ear protection.
The machine's noise and vibration levels, measured in
compliance with EN60745-1, usually reach:
Acoustic pressure = 85 dB(A)
Sound-power level = 98 dB(A)
Use ear protection!
Vibration acceleration = 2.5 m/s
ACCESSORIES
Accessories and their corresponding order number can
be found in our catalogues.

MAINTENANCE AND CARE

WARNINGAlways unplug the machine before carrying
out work on it.
- Tool inspection: Using a blunt cutting tool leads to
less efficient work and could damage the motor,
therefore cutting tools should be sharpened or re-
placed as soon as any wear is noticed. Daily: Clean
the tool holder.
- The milling heads must always be maintained sharp
for optimum work results.
- Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are firmly tight-
ened. Should any screw be loose, tighten it immedi-
ately. Failure to do so could put you at serious risk.
2
- Motor maintenance: Take the utmost care to ensure
that the motor winding is not damaged and does not
become damp with oil or water.
- Brush replacement: The brushes disconnect auto-
matically and should be replaced after 150 - 200 hours
use or when they are less than 10 mm long. Have
them replaced by an Official Service Centre.
- Clean the machine thoroughly after each use with a
blast of dry air.
- The vents of the machine should be kept clear at all
times.
- Check that the mains lead is in good condition. If it is
not, take it to an Official Service Centre to have it
replaced.
- Use only Felisatti accessories and spares. The
parts the changing of which is not covered in this
instruction manual, should be replaced in a Fe-
lisatti Official Service Centre (See Warranty Official
Service address leaflet).
Do not dispose of electric tools in
the household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances and
its translation into national law, used electric tools must
be collected separately and recycled in an ecologically
desirable way.

WARRANTY

See general warranty conditions printed on the attached
sheet.

DECLARATION OF CONFORMITY

We hereby declare, under our own responsibility,
the FELISATTI products described in this manual
RF55/1000E comply with the following standards
or standard
EN60745-2-17:2003,
EN55014-2:1997+A1+A2,
2:2006+A1+A2 and EN61000-3-3:2008 and in
accordance with EU Directives 2006/42/EC,
2006/95/EC, 2004/108/EC and 2002/95/EC.
11
We reserve the right to make technical changes 09/2011
documents EN60745-1:2008,
EN55014-1:2006+A1,
EN61000-3-
Francisco Ruiz
Plant Mgr.