Schartec Sky Anleitung Seite 9

Wiring Instruc�ons for Garage Door Opener or Gate Opener
for house door wiring/activation instructions, please jump to page 4
Connec�ng the keypad to a Garage Door Opener or Gate Opener
1. Ensure that the power to your garage door opener or gate opener is removed. Do not a�empt to connect the
keypad to the opener while the power supply is s�ll being provided to the opener!
2. Connect the RED wire from the keypad to the 12-24V posi�ve supply and the BLACK wire to GND.
3. Depending on if your opener has an NO or NC connec�on will determine the next step: in most cases, garage
door and gate openers have an NO (normally open) connec�on, meaning that keypad will need to "close" the
circuit in order to trigger the opening/closing of the opener. For NO type openers, connect the BLUE wire from
the keypad to the NO slot on your opener. !!!Please refer to your openers manual for this step!!!
4. Now connect the PURPLE wire from the keypad to the GND slot on your opener.
5. The remaining wires on the keypad ARE NOT NEEDED for the opening and closing of the garage door or gate
opener and should therefore be simply clamped off so that they are not connected/touching each other or
anything else. Please use either electrical tape or a wire cap.
Ac�va�on
1. Once the keypad has been properly connected, reconnect your opener to the power supply. The LED on the
keypad will light up red, then show yellow, then back to red followed by a beep. The keypad is now ready to
receive input.
2. You will need to begin with the administrator code: press *, followed by 888888 and the # key. The keypad is
now in the se�ng mode and is wai�ng for further commands. This code can be changed and is explained a�er
step 6.
3. You now need to add in a user and their passcode. Up to 2000 users can be added with individual passcodes OR
transponder. Each user is saved in a "slot" numbered from 1 to 2000, so it's important to keep track of the user
number and their passcode OR transponder number.
4. Within 10 seconds (a�er comple�ng point 2) press the 1 key on the keypad. Now enter the number of the user
you want to assign (1-2000) and then confirm with the # key. Now enter your 4-6 digit passcode, followed by
the # key. The LED will briefly flash green to confirm that your access code has been saved. The LED will light up
yellow again and is now wai�ng for more users/passcodes. You can now press any number between 2-2000,
followed by the # key, and then enter in another passcode again followed by #. Please make sure that you note
the user slot as well as the passcode.
5. Now that your users and passcodes have been entered, the keypad needs to be set to "impulse mode", which is
the mode needed for garage door and gate openers. The factory se�ng for the keypad is for house doors,
which is not the correct se�ng for GDOs. Once the keypad is back at it's beginning state (red light on
con�nuously), press again the * then the administrator code 888888 followed by the # key. The LED lights up
green briefly, then flashes red. Now press 4, then 0, then #. The keypad will briefly illuminate green confirming
your selec�on, then will return to flashing red. They keypad has now been set to impulse mode and is ready to
begin opening and closing your GDO.
6. Before undertaking the next step, ensure that you are in sight of your garage door or gate opener and that
nothing is in the way of the gate or garage. Now simply enter your passcode followed by the # key. The garage
door or gate opener will now begin opening/closing!
NOTES: changing the admin code: press * followed by the factory se�ng admin code of
888888 and then #. Now press 0, followed by a new 6 to 8 digit code and the # key, and then
renter the new code again followed by the # key. The keypad will briefly illuminate green
confirming your selec�on, then will return to flashing red. The admin code has now been
changed. Please document this code and keep it safe as the only way to recover it is to do a
complete factory reset.
HOW TO do a factory reset: disconnect the power supply from the code-keypad. Switch the
power supply back on. When the LED lights up yellow, press and hold the * bu�on un�l 2
short beeps are heard, then release the * bu�on. There will be a longer beep. The code-key-
pad is now reset to the factory se�ng. NOTE! STORED PASSWORDS OR TRANSPONDERS ARE
NOT RESET BY THIS!
HOW TO reset/delete passcodes or transponders: Press *, then your administrator code,
followed by the # key. Now press 2. Now enter in the user number you would like to delete,
followed by the # key. The selected user and their passcode have now been deleted. To
delete a transponder, a�er pressing 2, you can simply scan the transponder and it will be
deleted from the memory. To delete ALL passcode and ALL transponders, a�er pressing 2,
press 0000 followed by the # key - WARNING this will delete ALL saved users and their
passcodes as well as transponders!