Schartec Sky Anleitung Seite 11

START: Press * → Enter
admin code → RED
flashes → press
desired menu key
below → proceed to
next step
New passcode (6-8 digits) → # → repeat
0 →
1 →
2 →
3 →
4 →
START: Press * → Enter
During YELLOW flash →
admin code → RED
press desired menu key
flashes → press
below → light remains
desired menu key
lit YELLOW → proceed
below → proceed to
next step
7 →
8 →
** A�er pressing a key or reading a transponder, the keypad light will turn off a�er 30 seconds. However, when the keypad light is off, you will first need to
For addi�onal assistance with setup and installa�on, please check out our website www.schartec.de or search for
Problem
User passcode not working
User passcode not working
Reading distance of transponder close, but
not working
No reac�on a�er using transponder
Keypad not illumina�ng
Unable to enter administrator mode
Any other problem...
Opera�onal Se�ngs
LED illuminated YELLOW
new passode → # →
Touch Transponder to Keypad →
1-2000 (User ID) → # → Touch
Transponder to Keypad →
1-2000 (User ID) → # → 4-6 digit
passcode → # →
Touch Transponder to Keypad →
1-2000 (User ID) → # →
0000 → # →
0 → # →
1 → # →
2 → # →
0 → # →
1-99 → # →
LED illuminated
to next step
4 →
1 →
2 →
3 →
4 →
5 →
press any key or read a transponder, and then enter the passcode or read the transponder again.
Using in�al passcode of 1234
Keypad is set to either Transponder Only or
Transponder AND Passcode mode
Transponder quality issue
Keypad is not in the standby state
Keypad light func�on disabled
Forgot/misplaced administrator passcode
Contact us! Support in English and German!
Func�on
Modifies Administrator passcode
Adds 1 Transponder
Adds 1 user and passcode
Deletes 1 Transponder
Deletes 1 User and passcode
Delete ALL Transponders, users, and
passcodes
Only Transponder can be used for access
Tranponder AND passcode must be used
for access
Tranponder OR passcode can be used for
access
Relay �me set to 50 milliseconds
Relay �me set to 1 to 99 seconds (based
on entered number)
System Se�ngs
YELLOW
0 → # → Turns OFF An�-Tamper Alarm SOUND
Turns ON An�-Tamper Alarm SOUND for 1-3
1-3 → # →
0 → # → Sets Indicator Light Normally OFF
1 → # → Sets Indicator Light Normally ON
Sets Keypad Beep Noise OFF (except when in
0 → # →
1 → # → Sets Keypad Beep Noise ON
0 → # →
Sets Keypad Light Normally OFF
1 → # →
Sets Keypad Light Normally ON
2 → # → Sets Keypad Light to Automa�c mode**
0 → # → Turns OFF An�-Tamper Alarm
1 → # → Turns ON An�-Tamper Alarm
0 → # → Sets to Unlimited False-Code numbers
A�er 10 False-Code entries, keypad locked for
1 → # →
A�er 10 False-Code entries, alarm for 1-3 min
2 → # →
SCHARTEC in YouTube!
Troubleshoo�ng
Possible Cause
Remark
Rota�ng Opera�on = mutliple users/passcodes
or transponders can be added without having to
re-enter menu 1.
Rota�ng Opera�on = mutliple users/passcodes
or transponders can be added without having to
re-enter menu 2.
Factory se�ng is 2
Factory se�ng is 5.
Se�ng for garage door and gate openers -
switch to 0.
Func�on
minutes
admin mode)
10 min
(see Menu 7)
Solu�on
1. User passcode cannot be set to 1234
2. User passcode must be set between 4-6 digits
1. Change mode to Transponder OR Passcode mode
2. If in Transponder AND Passcode mode, make sure to
use transponder in combina�on with passcode
Use only original Schartec Transponders
Press * to exit - the LED will illuminate RED and return
to the standby state.
Check LED illumina�on se�ngs under the system
se�ngs table - this func�on will need to be reac�vated
Reset to factory se�ngs, default admin passcode is
888888. Cau�on! Doing a factory reset will reset all of
the se�ngs done to the keypad but NOT the saved
users and the passcodes/transponders!
info@schartec.de
Remark
Factory se�ng is 1
Factory se�ng is 1
Factory se�ng is 1
Factory se�ng is 1
Factory se�ng is 0
Factory se�ng is 0