ARESA AR-4001 Bedienungsanleitung Seite 6

ENGLISH
Unpack the device and remove all labels. Before using the appliance for the first time, check that the power supply of your appliance
corresponds to the power supply in your network.
Fill the thermopot with water and boil it. Drain the water with a manual pump. Repeat the procedure 2-3 times. Your appliance is ready for use.
• Open the lid of the thermopot (9). To open the lid, pull the lever (5).
• Fill the inner pot of the thermopot with water using a kettle, jug or other container. Do not allow
water to enter the housing.
• After filling the pot with water, close the lid until it clicks.
• Connect the device to the mains.
• The boiling cycle starts. The corresponding indicator on the front panel (boiling) lights up.
After the water boils, the device automatically goes into the temperature maintenance mode, while the indicator for maintaining the
temperature lights up.
Water can be poured only if the boiling cycle is completed and the device is in a state of maintaining the
temperature, i.e. heating. To pour water, press the water pump (6).
To lock the pump for water supply, set the pump lock (8) to the appropriate position (see photo).
SWITCH OFF FUNCTION IN CASE OF INSUFFICIENT WATER QUANTITY
When you turn on the boiling function of the appliance with an empty water tank, it will automatically shut off from the mains. As the
temperature decreases, the boiling function automatically switches on again, so it is necessary to fill the tank in time.
Important! For boiling it is recommended to use only water that has passed the filtration cycle with a household filter or bottled water.
FAULT
Water doesn't heat up
Hot water flows by itself
Unusual smell from the water
TRANSPORTATION. Transportation of the device is necessary by any kind of covered transport with the application of rules fastening of cargoes ensuring
preservation of the presentation of the product and / or packaging and its further safe operation. DO NOT expose the device to shock loads during handling
operations.
CLEANING. After use and before cleaning, remove the power plug from the outlet and wait for the appliance to cool.
Do not place the device in water. Cleaning the body and cover. Wipe the cover and body with a normal dry or damp cloth.
Do not overfill the thermo water with water, as it can overflow the edges to the base and into the water outlet as well as to the electronic parts inside the unit,
which will damage them. Do not use abrasive cleaners for cleaning. Do not clean the kettle with gasoline or turpentine (there may be an odor). It is forbidden
to wash the thermopot under direct water jet. This will cause it to damage and risk getting an electric shock.
Cleaning of the inner tank.
Wipe the water tank with a damp sponge. Do not use a scraper or nylon brush.
After use for some period, scale may appear on the bottom of the inner tank. It is recommended to clean the appliance as scale is formed, but at least every 2
months of use.
After you rinse the device, dry it.
STORAGE. The device must be stored indoors, in conditions that presume the preservation of a presentation product and its further safe operation. Make
sure that the appliance and all its accessories are completely dried, before storing it.
When purchasing the product, ask for it to be checked in your presence. Without the having a warranty card or when it is not properly filled in,
the quality claims are not accepted, and no warranty repair is performed. The warranty card should be presented at any address to the service
center during the whole warranty period. The product is accepted for service in a complete set only. The warranty period is calculated from the
moment of sale to the buyer. Keep the documents confirming the date of purchase of the product (cash receipt).
The condition of free warranty service of your product is its correct operation, which does not go beyond personal domestic needs, in accordance
with the requirements of the operating instructions for the product, the absence of mechanical damages and the consequences of careless
handling of the product.
The product is accepted for warranty service in its pure form. The warranty covers all manufacturing and construction defects (except those
listed in the "Warranty does not apply" section), identified during the warranty period. During this period defective parts, except consumables,
are subject to free replacement in the warranty service center.
FIRST USAGE
OPERATION
TEMPERATURE MAINTENANCE FUNCTION
WATER SUPPLY AND BLOCKAGE
FAULTS AND PROCESSING METHODS
WATER SUPPLY AND BLOCKAGE
CAUSE
The power cord is not plugged into the outlet or to the appliance
The water level is above the maximum level
Smell of plastic during the first use
TRANSPORTATION, CLEANING AND STORAGE
WARRANTY TERMS
METHOD
Connect the power cord correctly
Drain the water to or below the maximum water level
Boil and drain the water (2p)