Specifications; Advanced Configuration - Renkforce 2373321 Bedienungsanleitung

b) Configuring as repeater
• Click on "Repeater" in the setup wizard.
• The AP will automatically search for available Wi-Fi networks. The list will be displayed as
soon as the search is complete.
• First select the mode.
"Gateway": This option serves to set up a separate network similar to the router. The AP
retains its fixed IP address "192.168.10.1" after configuration. The DHCP server remains
active. The devices connected to the repeater receive their IP address from the repeater. For
further configurations, log in to the web interface.
"Bridge": The repeater and all devices connected to the repeater receive an IP address from
the Wi-Fi router. This option enables easier access to the repeater after configuration. The
repeater's IP address can be found in the network device list of your Wi-Fi router.
We recommend that you use this mode.
• Click on the Wi-Fi network you want to connect the repeater to in order to expand or
strengthen the Wi-Fi network.
You can simply scroll down a longer list. If there is a „5" in the WLAN symbol, it is a
5 GHz network, if there is a „2", it is a 2.4 GHz network.
• Enter the password to access the selected Wi-Fi network.
• Now you can adjust the names of the 2.4 and 5 GHz WiFi network provided by the repeater.
By default, the original WLAN is extended with "_EXT2.4G" or "_EXT5G". Generally, you can
use the original Wi-Fi names. This also applies if these are identical for your wireless router.
The same password is used for the two new WiFi networks as for the original WiFi.
• Click on the blue button to save and connect. The AP will restart with the new settings. The
process can take up to 2 minutes.
Reconnect your device to the AP's Wi-Fi network and enter the password of your
Wi-Fi router.
c) Configuring as router
• Insert one end of the network cable into the "LAN DATA IN" RJ45 connection on the PoE
adapter and the other end into the RJ45 connection of your modem.
• Click on "Router" in the setup wizard.
• First select the connection type.
For a DSL-modem with a dial-up, click on the "PPPoE" above and then enter your dial-up
name and password.
If Internet access requires a fixed IP address, select the middle menu item and enter all
required IP address data.
If Internet access requires a dynamic IP address, select the right menu item (default). No
further entries are required.
• Now choose a name for the 2.4 and 5 GHz WiFi network. You can also assign the same
name to both.
• Then select the encryption "WPA2-PSK" and enter a Wi-Fi password in the field below.
The password must be at least 8 characters long. We recommend that you use a
password with more characters, consisting of numbers and upper and lower case
letters.
The Wi-Fi connection should not be left unencrypted (open).
• Click on the blue button to save the setting. The AP will restart. The process can take up to
2 minutes.
• Reconnect your device to the AP's Wi-Fi network and enter the previously set password.
• Once connected, click on the blue button to refresh the display.
• For further configurations, log in to the web interface.

Advanced configuration

Clicking on the gear icon at the bottom right of the web interface opens advanced settings.
In addition to the login password, you can also change the settings for the WAN port, save and
restore the configuration, update the firmware, display an extended device status, log out of the
web interface and restart the device.
Clicking on the button with the Wi-Fi signal below opens the Wi-Fi settings menu. This menu
enables to edit the Wi-Fi name, change the password or set the Wi-Fi channel manually.
Resetting to factory defaults
The device can only be reset to factory defaults if it is connected and in operation. Proceed
as follows:
a) Resetting with the product
• Hold the "Reset" (J) button on the product for about 8 seconds and then release the button.
All LEDs light up first and then go out again after a short time.
• The product will restart and the factory settings will be restored. This process takes up to 2
minutes. When the 4 WLAN LEDs (C) and (D) light up continuously again, the process is
complete.
b) Resetting in the web interface
• Open the product's web interface and log in.
• Click on the gear icon at the bottom right to open the configuration menu.
• Select the point for backup and then click on the bottom blue button to load the factory
settings.
• The product will restart and the factory settings will be restored. This process takes up to 2
minutes. When the 4 WLAN LEDs (C) and (D) light up continuously again, the process is
complete.
Care and cleaning
• Disconnect the product from the power supply before cleaning.
• Use a dry, lint-free cloth to clean the product.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declares that this
product conforms to Directive 2014/53/EU.
Click on the following link to read the full text of the EU Declaration of Conformity:
www.conrad.com/downloads
Select a language from the menu and enter the order number of the product in
the search field. You can then download the EU Declaration of Conformity in PDF
format.
Disposal
Electronic devices are recyclable waste and must not be placed in household waste.
At the end of its service life, dispose of the product in accordance with applicable
regulatory guidelines.

Specifications

a) Product
Operating voltage ......................... 24 V/DC (Passive PoE)
Power consumption ...................... max. 7 W
Connections .................................. 1x RJ45 10/100 Mbps, WAN/LAN/PoE
WLAN ........................................... IEEE802.11b/g/n/ac; 2,4 GHz (max. 150 MBit);
5 GHz, (max. 433 MBit) Dual-Band
Frequency range/
transmission power ....................... 2.412 - 2.472 GHz, ≤ 30 dBm;
5.725 – 5.850 GHz, ≤ 30 dBm
Encryption protocols ..................... WPA-PSK; WPA2-PSK; WPA/WPA2
Modes of operation ....................... Access Point (AP), Repeater, Router
Chip set ........................................ MT7688A + 7610E
Memory ......................................... Flash 64 MB, DDR2 512 MB
Protection rating ........................... IP65
Device dimensions (W x H x D) .... approx. 55;5 x 180 x 48 mm (without antennas and bracket)
Antenna dimensions (Ø x L) ......... approx. 13 x 250 mm
Weight .......................................... approx. 197 g (with antenna, without bracket)
Operating conditions ..................... -30 to +70 °C, 10 to 90% RH (non-condensing)
Storage conditions ........................ -40 to +70 °C, 10 to 90% RH (non-condensing)
b) Power adapter
Operating voltage ......................... 100 – 240 V/AC, 50/60 Hz
Current consumption .................... max. 0.5 A
Output ........................................... 24 V/DC, 500 mA, 12 W
Output connector .......................... 5.5 x 2.5 mm coaxial power connector
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2021 by Conrad Electronic SE. 2373321_V2_1121_02_m_VTP_en