Werbung
Verfügbare Sprachen
Verfügbare Sprachen
All manuals and user guides at all-guides.com
Driver installation under Windows 98SE:
One of this range, which you can use for your
When booting the system there appears a
network is 192.168.1.1 to 192.168.1.254. The first
window "New Hardware Found". The network
computer then gets the address 192.168.1.1, the
card gets identified as "PCI Ethernet Controller".
second 192.168.1.2, the third 192.168.1.3 and so
Shortly after Windows starts the Add New Hard-
on.
ware Wizard and searches for new drivers for
"PCI Ethernet Controller". Please click on
Installing and configuration of the TCP/IP
Next. In the following window ("What do you
protocol
want Windows to do?") select "Search for the
Click on
best driver for your device"
Next. Insert the
Network. In the new window, please check if
enclosed floppy disk. Then
only
mark
"Specify a
there is an entry "TCP/IP -> Realtek RTL8169...".
location "
and type in
"A:\Win98"
Next
The name of the entry is "TCP/IP" if the network
Next. The necessary files are copied from the
card is the only network device. The TCP/IP
disk now.
protocol is not installed if such an entry is
Insert the
Windows 98 CD-ROM
if needed and
missing. To add it to the system, click
then click on
"OK"
(Possibly you must then enter
Protocol
another drive letter for your CD-ROM drive).
(Manufacturers) mark
Then click on
Finish
. Take the disk out of the
(Network Protocols) please select
drive and answer the question about the restart
Then click on
with
"Yes"
.
Afterwards assign an IP address to the network
card. Highlight "TCP/IP -> Realtek RTL8169..."
Verifying the installation (Windows 98SE/ME)
resp. "TCP/IP"
You can check if the network card has been
Specify an IP address
installed properly. Click
Start
Settings
number according to above instructions, for
Control Panel
System
Device Manager
example 192.168.1.1 for the first computer and
Network adapters. There must be an entry
for the second 192.168.1.2 and so on. At Subnet
"Realtek RTL8169 Gigabit Ethernet Adapter"
Mask
enter
without a yellow exclamation mark.
OK.
Basic configuration of a new network
Installing the Client for Microsoft Networks
(Windows 98SE/ME)
For accessing files and/or printers of other
After the proper installation of the network card,
computers on the network, the
you have also to configure the LAN settings.
"Client for Microsoft Networks" has to be
That includes to install and setup a network
installed.If it is not listed at the network
protocol. With it, the computers of a network
components, you can add it by clicking
interchange data. Most frequently, TCP/IP is
Client
used. Also the most topical multi-player games
(Manufacturers) select
communicate via this protocol. There must be an
(Network Clients) mark Client for Microsoft
own address assigned for each computer when
Networks
using this protocol. The automatical address
Afterwards you have to configure the network
setting only functions reliable if there is a DHCP
logon. At P
server available in the network. Normally there
"Client for Microsoft Networks".
is no such server existent. It is recommended to
manually assign an address to the network card.
The following example shows the basic setup by
configuring the IP addresses manually. For local
networks there are special number blocks,
which are not routed in the internet.
Enable file and printer sharing
To provide files and/or printers of your computer
to other users on the network, click on File and
Print Sharing
printer sharing for your computer if this function
is not already active. Afterwards please click on
OK. Later you can share folders, drives and
printers.
Start
Settings
Control Panel
Setting up computer name and workgroup
Click on
each computer has been given a unique name,
not to conflict with each other. Make sure the
workgroup name is the same for all the
Add
computers in the network. Furthermore the
Add. In the left window
workgroup name must not be the same as a
Microsof
t. At the right
computer name. Then click on
TCP/IP
.
settings are finished now.
OK
.
Insert the
then click on
another drive letter for your CD-ROM drive).
and then click on
Properties
Answer the following question about the restart
. At
"IP Address"
enter a
with
"Yes"
Share folders, drives or printers:
In the Windows Explorer mark the folder, the
255.255.255.0
. Then confirm with
drive or the printer that shall be shared and then
click the right mouse button. Then click
Sharing. Now select "Shared As:", enter a share
name and change the access type if needed
Apply
resources in the Windows Explorer with a hand
in the symbol.
Add
Accessing shared folders and drives:
Add. In the left window
Click on "My Network Places" resp. "Network
Microsoft
. At the right
Neighborhood" in the Windows Explorer or on
the desktop. Then choose the corresponding
OK.
resources.
rimary Network Logon
choose
Setting up shared printers:
Please click on
Add Printer
Next
connected to the printer and then the
corresponding model
from MS-DOS-based programs?" select Yes or
No according your requirements
enter a name for the printer
you would like to print a test page
The printer gets installed now. The installation
may differ for some models resp. when using
: You can
enable
the file and/or
different Windows versions.
Identification
. Please ensure that
OK
. The basic
Windows CD-ROM
if needed and
"OK"
(Possibly you must then enter
.
OK. The system shows the sharing of
Start
Settings
Printers
Next
Network printer
Browse. Select the computer which is
OK. At "Do you print
Next. Then
Next. Select if
Finish.
Werbung
