Werbung
Verfügbare Sprachen
Verfügbare Sprachen
All manuals and user guides at all-guides.com
Checking the installed network components
Share folders on the network
Click on
Start
Control Panel (in the classic
In the Windows Explorer mark the folder which
start menu
Start
Settings
Control Panel)
shall be shared on the network. Then click the
Network and Internet Connections
right mouse button. Click
Network Connections (In the classic view
ty. Now select "Share this folder on the network",
double click on Network Connections).
enter a share name and change the option
Afterwards click with the
right mouse button
on
"Allow network users to change my files" corre-
Local Area Connection
. Then click
Properties
.
sponding to your requirements. Afterwards click
There must be following items be installed and
Apply
active (A tick in the small box left of the item):
resources in the Windows Explorer with a hand
Client for Microsoft Networks
in the symbol of a folder.
File and Printer Sharing for Microsoft Networks
Internet Protocol (TCP/IP)
Accessing shared folders
Normally these items are already installed.
Click "My Network Places" in the Windows
When a component is missing, please click on
Explorer. Then choose the corresponding
"Install" and choose the corresponding item to
resources.
add it.
Installation under Windows 2000 Professional:
Configuring the TCP/IP protocol
After the windows start, the system executes the
Mark
"Internet Protocol (TCP/IP)"
and click on
"Found New Hardware Wizard". Please click on
Properties. Then select "Use the following IP
Next. In the following window select "Search
address" and enter an IP address corresponding
for a suitable driver for my device "
to above instructions. For example, the first com-
Then mark only "Specify a location"
puter gets 192.168.1.1. Then enter the correct
Insert the enclosed floppy disk into the drive and
subnet mask 255.255.255.0. Confirm with
OK
type in the path "A:\Win2000"
Close.
Finish.
To check if Windows has set up the card
Starting the Network Setup Wizard
properly, click
Click on
Start
Control Panel (in the classic
Panel
start menu
Start
Settings
Control Panel)
Manager
Network and Internet Connections
Set up
an entry "Realtek RTL8169 Gigabit Ethernet
or change your home or small office network
Adapter" without a yellow exclamation mark.
(In the classic view
Network Connections
Set up a home or small office network).
Basic configuration of a new network
Now please follow the advises of the network
After the proper installation of the network card,
setup wizard and choose the options which
you have also to configure the LAN settings.
match with your requirements.
That includes to install and setup a network
Please ensure that each computer has been
protocol. With it, the computers of a network
given a unique name, not to conflict with each
interchange data. Most frequently, TCP/IP is
other. Make sure the workgroup name is the
used. Also the most topical multi-player games
same for all the computers in the network.
communicate via this protocol. There must be an
Furthermore the workgroup name must not be
own address assigned for each computer when
the same as a computer name. Afterwards
using this protocol. The automatical address
please check the TCP/IP protocol settings. Pos-
setting only functions reliable if there is a DHCP
sibly you have to assign the correct IP address
server available in the network. Normally there
again.
is no such server existent. It is recommended to
manually assign an address to the network card.
The following example shows the basic setup by
configuring the IP addresses manually.
For local networks there are special number
blocks, which are not routed in the internet.
One of this range, which you can use for your
Sharing and Securi-
network is 192.168.1.1 to 192.168.1.254. The first
computer then gets the address 192.168.1.1,
the second 192.168.1.2, the third 192.168.1.3
and so on.
OK. The system shows the sharing of
Checking the installed network components
Click
Network and Dial-up Connections. Click with
the
right mouse
Connection
be following components be installed and active
(A tick in the small box left of the item):
Client for Microsoft Networks
File and Printer Sharing for Microsoft Networks
Internet Protocol (TCP/IP)
Normally these items are already installed.
When a component is missing, please click on
"Install" and choose the corresponding item to
Next.
add it.
Next
.
Configuring the TCP/IP protocol
OK
Next
Mark
"Internet Protocol (TCP/IP)"
Properties
address"
Start
Settings
Control
to above instructions. For example, the first
System
Hardware
Device
computer gets 192.168.1.1. Then enter the
Network adapters. There must be
correct subnet mask 255.255.255.0.
Confirm with
Set computer name and workgroup
Click
System
Please ensure that each computer has been
given a unique name, not to conflict with each
other. Make sure the workgroup name is the
same for all the computers in the network.
Furthermore the workgroup name must not be
the same as a computer name. Afterwards
please click on
notice that you have to reboot the computer for
the changes to take effect. Click on
the window "System Properties" also with
Answer the following question about the restart
with "Yes".
Share folders, drives and printers on the
network
To be able to access shared resources of a
computer running Windows 2000, you have to
add the corresponding users first. You can
manage the
users
and Passwords.
Afterwards mark the folder, the drive or the prin-
ter that should be shared and click with the right
Start
Settings
Control Panel
mouse button on it. Then click on
Enter a
share name
button on
Local Area
if necessary. The system shows the sharing of
and then
Properties
. There must
resources in the Windows Explorer with a hand
in the symbol.
Accessing shared folders and drives:
Click on "My Network Places" in the Windows
Explorer or on the desktop. Then choose the
corresponding resources.
Set up shared printers:
Click on
Start
Printer
Next
Next. Select the computer which is connected to
and click on
the shared printer and then the corresponding
. Then select
"Use the following IP
printer
Next. Configure it as the default
and enter an
IP address
corresponding
printer if needed
installation may differ for some models resp.
when using different Windows versions.
OK
OK
.
Installation under Windows 98SE/ME
Driver installation under Windows ME:
After starting the computer, the system executes
Start
Settings
Control Panel
the Add New Hardware Wizard. In the window
Network identification
Properties.
"What would you like to do?" select
the location of the driver (Advanced)" and then
click on
Next
. In the next window select
"Search for the best driver for your device" and
mark only "Specify a location". Insert the enclo-
sed floppy disk into the drive and type in the
directory "A:\Winme"
OK
. The system shows a
Remove the disk from the drive and answer the
question about the restart with
OK
. Close
OK
.
at the
Control Panel/Users
Sharing
.
and change the
permissions
Settings
Printers
Add
Network printer
Next
Next
Finish. The
"Specify
Next
Next
Finish
.
Yes
.
Werbung
