Werbung
Verfügbare Sprachen
Verfügbare Sprachen
fourth additional addresses can be entered
respectively.
First additional address (code 001).
To program the first additional call address (by
default empty; allowed addresses between
001 and 200) it is necessary:
enter code 001;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Room number (code 005)
This is the room address of the device and
is used to identify it within the flat (factory
setting 000 - MASTER, allowed addresses
between 000 and 004).
Enter code 005;
press button
to confirm;
enter the new room number;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the room numbers of the
additional user addresses (codes 006-
009).
With regard to the 4 additional addresses,
the videointercom can act as MASTER or as a
secondary device (room 001-004) to answer
calls correctly. The storage procedure is shown
below for the room number related to the first
of the four additional addresses (code 006).
Using codes 007, 008 and 009, it is possible to
enter the room numbers for the second, third
and fourth additional addresses respectively.
Room number relative to the first addi-
tional address (code 006).
To program the room number for the first ad-
ditional address (by default empty; allowed
addresses between 000 and 004), it is nec-
essary:
enter code 006;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming of addresses associated
with sequential pressing of the button
(codes 010, 011, 012 and 013).
If pressed with the system in stand-by, the
videointercom button
activates auto-on
to the last door unit from which the call was
received. It is possible to press the button four
more times to sequentially display up to four
additional door units whose addresses have
been previously stored as described below. By
default, the four addresses are empty.
Allowed values are:
- addresses 231-253: external unit address
on which auto switch-on is to be performed
(display without having been called)
- address 255: erasing of previously entered
value.
The procedure is described below for the first
of the four addresses to be stored (code 010).
By using codes 011, 012 and 013, it is possible
- 10 -
Mi 2577
to enter the second, third and fourth door unit
addresses respectively on which to perform
auto-on.
Programming the address associated to
the sequential pressing of the button
(code 010).
To program the first address associated to the
sequential pressing of the button (by default
empty), it is necessary to:
enter code 010;
press button
to confirm;
enter the new address; enter 255 if you want
to restore the empty memory cell;
press button
to confirm;
continue with the next programming or exit
programming.
Programming of addresses activated
by pressing button 1 (codes 014 and
016).
Button 1 on the videointercom provides the
possibility of activating two different services
(each identified by the relative address) accord-
ing to the time for which the button is pressed. In
particular, a distinction is made between short
pressure (<1 sec.) and long pressure (> 3 sec.).
The allowed values for the services that can
be activated are:
- addresses 001-200: call to another user
- addresses 201-210: call to switchboard;
- addresses 211-220: actuator activation
- addresses 231-253: auto-on (without
having been called) to the external unit.
- address 255: erasing of previously entered
value.
Programming the address associated
with short pressure of button 1 (code 014).
To program the address associated with short
pressure on button 1 (factory setting 211), it is
necessary:
enter code 014;
press button
to confirm;
enter the new address; enter 255 if you want
to restore the empty memory cell;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the address associated
with long pressure of button 1 (code 016).
To program the address associated with long
pressure on button 1 (by default empty), it is
necessary:
enter code 016;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming room numbers related
to the addresses activated by pressing
button 1 (codes 015 and 017).
If the short or long pressure, or both, are
assigned the same address with which the
videointercom is called from outside, the
service that is activated is the intercom call
within the same flat. In order to correctly
address this call, the room number associ-
ated to the short/long pressure of button 1
must be programmed with the room num-
ber corresponding to the intercom/video-
intercom to be called. Allowed values are:
- address 000-007: room numbers;
- address 255: delete previously entered value.
Programming the room number related
to the address associated with short
pressure of button 1 (code 015).
To program the room number related to the
address associated with short pressure on
button 1 (by default empty), it is necessary:
enter code 015;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the room number related
to the address associated with long pres-
sure of button 1 (code 017).
To program the room number related to the
address associated with long pressure on
button 1 (by default empty), it is necessary:
enter code 017;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming of addresses activated
by pressing button 2 (codes 018 and
020).
Button 2 on the videointercom provides the
possibility of activating two different services
(each identified by the relative address) accord-
ing to the time for which the button is pressed. In
particular, a distinction is made between short
pressure (<1 sec.) and long pressure (> 3 sec.).
The allowed values for the services that can
be activated are:
- addresses 001-200: call to another user
- addresses 201-210: call to switchboard;
- addresses 211-220: actuator activation
- addresses 231-253: auto-on (without
having been called) to the external unit.
- address 255: erasing of previously entered
value.
Programming the address associated
with short pressure of button 2 (code 018).
To program the address associated with short
pressure on button 2 (by default empty), it is
necessary:
enter code 018;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the address associated
with long pressure of button 2 (code 020).
To program the address associated with long
pressure on button 2 (by default empty), it is
necessary:
enter code 020;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
Werbung
