Battery Charger; Led Status - WARRIOR WEP8121LB Betriebsanleitung

OPERATION
ASSEMBLING THE BLOWER TUBE
You may use this product for the purposes listed below:
Clearing hard surfaces such as driveways and
walkways.
Keeping decks and driveways free from leaves and pine
needles.
TO INSTALL/REMOVE BATTERY PACK(Fig.4)
– Align the ribs of the battery pack with the mounting
slots in the blower's battery port.
– insert the battery into the battery opening until the
battery release button locks into place.
Battery release button
Fig. 4
TO REMOVE:
– Press the battery release button on the blower, this
will cause the battery to slightly protrude out of the
tool.
–
Grasp the blower firmly and pull the battery out of
the handle
WARNING
Always take care of your feet, children, or pets
around you when pressing the battery release
button. Serious injury could result if the battery
pack falls, NEVER remove the battery pack when in
a high location
WARNING
ALWAYS CHARGE BEFORE FIRST USE.
Always remove battery pack from the product when
you are assembling parts, making adjustments,
cleaning, or when not in use. Removing battery
pack will prevent accidental starting that could
cause serious personal injury
STARTING/STOPPING THE BLOWER (Fig.5)
– Ensure that the battery is installed in the blower
correctly.
– To start the blower, turn the speed button located
on the blower.
– Squeeze the trigger to start the blower.
–
Release the trigger to stop.
Trigger
ADJUSTING THE AIR VELOCITY (Fig.6)
–
If you want to get Max. speed, press the turbo
button
– Ensure that blower is blower on, the LED above the
tool will illuminate.
– Turn the Speed Selection Button to increase the air
velocity to the desired.
– Note: The current speed setting will remain
even if the unit is turned off.
10
Turbo Button
OPERATING THE BLOWER
– To keep from scattering debris, blow around the
outer edges of a debris pile. Never blow directly into
the center of a pile
– To reduce sound levels, limit the number of pieces
of equipment used at any one time.
– Use rakes and brooms to loosen debris before
blowing. In dusty conditions, slightly dampen
surfaces when water is available
– Conserve water by using power blowers instead
of hoses for many lawn and garden applications,
including areas such as gutters, screens, patios,
grills, porches, and gardens.
– Watch out for children, pets, open windows, or
freshly washed cars, and blow debris safely away.
– After using blowers or other equipment, clean up.
Dispose of debris properly.
Fig. 5

BATTERY CHARGER

SPECIFICATIONS
Charger: C8360/C8362
Input: 120-240VAC, 50/60Hz, Max.3A
Output: 63VDC. Max.4.5A
Weight: 2.6 lbs (1.2kg)
CHARGING PROCEDURE (See Figure .7)
NOTE: The battery is not shipped fully charged. Fully
charge before first use to ensure that maximum run time
can be achieved. This lithium-ion battery will not develop
a memory and may be charged at any time.
Fig. 6
Charging Fully Charged
Battery Hot

LED STATUS

DESCRIPTION
Blinking Green Charging
Solid Green Fully charged
Solid Red Stand by
Blinking Red (fast) Charging fault
Blinking Red (slow) Battery too hot
Low voltage charging:
If the battery has been stored with little to no charge for
a long period of time, the charger will go into recovery
mode, which will take more time to fully charge the
battery. This will enhance the life of the battery. Once it
is fully charged, the next charge will return to standard
charging.
A fully discharged battery pack will require the allotted
time as stated in the battery manual. Plug the charger
into an AC power outlet.
Insert the battery -into the charger.
This is a diagnostic charger. The Charger LED Lights will
illuminate in specific order to communicate the current
battery status.
False defect note:
When the battery is inserted into the charger and the
status LED blinks RED, remove the battery from the
charger for 1 minute, then reinsert. If the status LED
blinks GREEN, then the battery is properly charging. If
the status LED is still blinking RED, remove the battery
and unplug the charger for 1 minute. After 1 minute,
plug in the charger and reinsert the battery. If the status
LED blinks GREEN, then the battery is properly charging.
If the status LED is still blinking RED, the battery is
defective and needs to be replaced
11
OPERATION
EN
Charging Fault