Product Markings - Baker Hughes Druck DPI 705E Schnellstartanleitung

Introduction
The Druck DPI 705E / DPI 705E-IS pressure indicator uses
a silicon transducer to produce a pressure reading in
pressure units. These user instructions include the
operations for all DPI 705E / DPI 705E-IS Pressure
Indicators, safety instructions and the requirements for
intrinsically safe instruments.
The DPI 705E / DPI 705E-IS is equipped with ISO 228
G1/8 female pressure connectors up to 350 bar (5000 psi,
35 MPa). Above 350 bar (5000 psi, 35 MPa), autoclave
male pressure connectors are supplied. For NPT pressure
connectors, use Druck adaptor IO-ADAPT-9/16AUTOC.
For the full specification and user manual, refer to Druck
website:
WARNING
Do not use the non-intrinsically
safe DPI 705E in locations where explosive
gas, vapor or dust are present. There is a risk
of an explosion.
Some liquid and gas mixtures are dangerous.
This includes mixtures that occur because of
contamination. Make sure that the DPI 705E /
DPI 705E-IS is safe to use with the necessary
media.
It is dangerous to ignore the specified limits
(refer to data sheet) for the DPI 705E /
DPI 705E-IS or to use the DPI 705E /
DPI 705E-IS when it is not in its normal
condition. Use the applicable protection and
obey all safety precautions.
To prevent a dangerous release of pressure,
isolate and bleed the system before
disconnecting a pressure connection. A
dangerous release of pressure can cause
injury.
Do not apply pressure greater than the
maximum safe working pressure.
Do not apply pressure greater than 1.1 bar
(15.95 psi, 110 kPa) absolute to the REF
pressure port of differential pressure
indicators.
To prevent an explosion or fire, use only the
Druck specified battery.
Remove batteries from the pressure indicator
immediately when discharged and before
storage.
Safety
The DPI 705E / DPI 705E-IS has been designed to be safe
when operated using the procedures detailed in this
manual. Do not use this equipment for any other purpose
than that stated, the protection provided by the equipment
may be impaired.
The product contains a Lithium coin cell for data backup.
This cell is not user replaceable.
Druck.com/essential
Before installing and using the DPI 705E / DPI 705E-IS,
read and understand all the related data. This includes: all
local safety procedures and installation standards, and this
document.
Repair
Do not do repairs to this equipment. Return the equipment
to the manufacturer or an approved service agent.
Intrinsically Safe Devices
Product Feature DPI 705E
Intrinsically safe
Color
Static Dissipative
Battery Specification Refer to "Batteries" on page 2 and
"Replacing the Batteries" on page 2
Conformances

Product Markings

Refer to Figure A1 and key below:
This symbol, on the equipment, indicates a warning
and that the user should refer to the user manual.
Ce symbole, sur l'appareil, est un avertissement qui
indique que l'utilisateur doit consulter le manuel
d'utilisation.
1. Part Number, Maximum Working Pressure (M.W.P.),
Serial Number, Date of Manufacture (Month-Year).
2. EU Hazardous Area Markings.
3. IECEx Certificate Number.
4. ATEX Certificate Number.
5. UKEX Certificate Number.
6. EU Directive 2014/34/EU markings.
7. North American Hazardous Location Markings.
8. Protection Concept (Intrinsically Safe).
9. Ambient Temperature Range.
10. Control Drawing Number.
11. UKCA Mark and notified body number (####).
12. CE Mark and notified body number (####).
13. CSA Monogram (Canada and US).
14. CSA Project Number and US/Canadian Certificate
Number.
15. Pressure Connector Thread and Pressure Range.
16. Manufacturers Name and Address.
English–DPI 705E / 705E-IS Safety Manual | 1
DPI 705E-IS

Blue Yellow

CE
UKCA
CSA
IECEx
CE
ATEX
UKCA
UKEX
Refer to "Specific
Conditions of Use"
on page 2
Copyright 2019 Baker Hughes Company.