Kinderkraft AVEO Bedienungsanleitung Seite 21

● For the safety of children, do not leave parts of the packaging freely accessible (plastic bags, cardboard boxes, etc.). Risk
of suffocation!
I The main parts:
Part number
1 Frame
2 Rear wheels
3 Front wheel
4 Front fork
5 Mudguard
6 Front fork fixing screws and nuts
7 Handlebar fixing screw and nut
8 Handlebars
9 Mounting spanner
10 Bell with fixing screw
11 Basket
12 Basket fixing screw
13 Seat
II Installation of the tricycle:
How to video on: www.youtube.com/KinderkraftOfficial
Slide the rear wheels (2) in the frame (1) until you hear a click (Fig. A). Attach the mudguard (5) to the front fork (4) usi ng a
screw (21) and mounting spanner (9). Make sure that the notch on the mudguard is in the front (Fig. B). Slide the front wheel
components together, put the front wheel (3) in the fork (4) and tighten the front fork fixing screws (6), using mounting
spanner (9) (Fig. C). Slide the front fork into the bike frame. Then place the front basket (22) on the frame (1), by matching
the holes to the basket's knobs. Attach the handlebars (8) to the frame (1) using the spanner (9) and fixing screw (7), so there
is no play (Fig.D). Make sure the front wheel is in the straight position before mounting the handlebar. Fix the bell (10) to the
handlebars (8). Put the pull rod (20) by inserting its more curved end from above in the opening on the left side of the fork
(4) (Fig.E.I) and fix the other end under the frame (1) into the hole at the point of attachment of the parent handle (Fig. E.II).
Make sure that the clamp is installed correctly, if it is placed in the wrong hole, the handlebar and parental grip will not be
positioned parallel. Place the seat base (25) on the frame. make sure that the wider side of it is positioned correctly (Fig. F).
Use the fixing screw (12) to attach the basket (11) to the frame (1) (Fig. G). Push the seat screw through the hole in the base
and frame (1), and fix the seat forwards or backwards by tightening the nut (23) on the bottom of the frame (Fig.H) , attach
the backrest (15) (Fig.I). Then place the guardrails (14) in the holes in the seat (13) (Fig.J). Then put on the seat cover (16), by
placing the side covers through the safety rails, pull the material onto the seat and connect the cover to the backrest by
repositioning the safety belts (Fig.K). To install the seat belts correctly, unfasten the buckle at the back of the backrest, then
pass the belts through the holes in the backrest and fasten the buckle (Fig.L). Once the belts have been correctly positioned,
install the crotch protection strap by placing the material on one of the safety railings. The safety rails should be connected
together, a click sound means the elements have been fixed correctly. Insert the visor (17) in the sides of the backrest (15)
(Fig.M). Fix the cupholder (19) to the parent handle (18) and insert it in the hole on the frame until the latch is locked (Fig.
M). Attach the sachet (26) to the parent handle and close the Velcro fasteners.
Adjusting:
Cover location − press the red buttons on both sides of the cover and set in a convenient position. You can also use buckles
on top of the cover.
Footrests − depending on the level of child development, the footrests can be folded to enable the child to ride the tricycle.
WARNING! Whenever the parent's handle is mounted and the footrest is unfolded, the wheel lock should be disengaged so
that the pedals rotate freely without causing the wheel to move (transmission off). Without disengaging the lock, feet may
be crushed or injured! After removing the parent handle, fold up the footrest and engage the wheel lock so that the pedals
set the wheel in motion (transmission on).
Brake - the bike has a rear wheel brake. Press the brake with your foot. If you hear the lock sound, the brake is activated. It
is released when the brake lock is lifted.
Harness − adjust the length to hold the child firmly, but not to block movements.
Seat position − the seat can be adjusted forwards and backwards, and turned rearwards. To do this, unscrew the nut (22) and
set the appropriate position. After tightening, make sure the seat is securely fastened.
Folding the rear wheels − slightly lift the tricycle and push the red button under the frame, rotate the rear wheels forwards.
Older children can ride without a backrest − slide the seat cover down, remove the backrest unlocking the levers on its sides,
rotate the guardrails 90° backwards and pull out. To ride without the backrest, the child should wear additional harness which
is located under the seat.
Name
21
Part number
14 Guardrails
15 Backrest
16 Seat cover
17 Visor
18 Parent handle
19 Cupholder
20 Pull rod
21 Mudguard fixing screw
22 Front basket
23 Seat nut
24 Mounting spanner
25 Seat base
26 Sachet
Name