Elora 2080 Bedienungsanleitung Seite 2

ELORA-No. 2080
READ BEFORE YOU USE
1. This torque wrench is a precision instrument intended to be used
only to tighten screws, bolts and nuts to a desired torque.
2. Do not use it as a „nut breaker", pry bar, hammer, or in lieu of a
regular ratchet wrench.
3. Do not apply torque in excess of the maximum capacity of the
wrench. Apply load on the grip only, and do not use any handle
extension bars (a piece of pipe put over the grip).
4. Make sure that you adjust the wrench to the exact torque units your
specifications call for, or you will severely under-torque or
over-torque, causing severe damage to the equipment you are
working on.
5. Do not disassemble the wrench for any reason. Highly stressed
internal components may cause severe injury when released in an
unintended manner.
6. The wrench should be re-calibrated periodically. The calibration of
the wrench should be checked at least once a year, after any
abnormal handling or overloading, or after 5,000 cycles („clicks").
USE OF EXTENSIONS
Attachments and non-standard heads will cause the applied torque to be different from the set torque.Consequently when using them,the set torque must be adjusted in
accordance with the formula shown on below.
T(E) - Torque applied by extension
(desired torque)
T(W) - Torque set on the wrench
SAFETY WARNING
Overtorqued or defective fasteners, sockets, as well as the wrench itself, may suddenly break causing you to lose balance, fall, or to suffer other trauma. Be sure that you have firm footing,
are properly balanced, and if necessary are using appropriate harness, back support, or other safety device.
MAINTANANCE
1. When not in use, adjust the wrench to its lowest reading , and store it in the provided case.
2. Do not lubricate the wrench, exept the ratchet mechanism. Use only a few drops of light machine oil.
3. Do not use acetone or other solvents to clean the wrench, use window cleaner or denatured alcohol applied with a clean cloth instead.
4. With the exception of the ratchet mechanism, there are no user-serviceable parts. Do not disassemble the torque wrench for any reason. When service is needed, send the wrench to the
nearest factory-authorized service center.
CERTIFICATION
This torque wrench is certified to have been calibrated prior to shipment to the accuracy of +/- 3% in the clockwise direction .
Torque Wrench
Instruction Manual
Major torque units
Hardened alloy steel housing
SETTING TORQUE
1. Pull the lock knob out.
2. Turn the grip in the clockwise direction to increase the torque, and in the counterclockwise to
3. The major scales show the amount of torque in both primary and secondary units.
4. Push the lock knob in to lock the grip. The minor scale may be slightly off the centerline mark
Minor torque units
nonslip
QUATROLIT
decrease it. Please set torque going up the scale. If you exceed desired torque, please adjust
torque to one revolution below the desired torque, then back up.
The minor scale shows fine increments in primary units.
without affecting the accuracy of your settings.
APPLYING TORQUE
1. Insert an appropriate socket or drive attachment onto the square drive of the ratchet and
onto the fastener
2. Apply hand pressure to the grip, and ONLY TO THE GRIP. You may support the wrench at the
ratchet head with the other hand to steady it, especially when using long socket extensions,
without appreciably affecting the accuracy of the wrench.
3. If, due to the required effort, you need to use both hands, put the other hand on the top of
the first hand, never on any other part of the wrench.
4. Apply slow and steady pull or push until the wrench momentarily releases, with or without
a distinct „click" sound. Release the pressure right at this point.
DO NOT OVERTORQUE!
ELORA WERKZEUGFABRIK GMBH
Am Blaffertsberg 33, 42899 Remscheid
Tel.: +49 (0)2191.5627 - 0
Fax.: +49 (0)2191.5627 - 19
info@elora.de
www.elora.de
Lock knob
-2C-handle
®