nedis HTBA20WT Kurzanleitung Seite 6

Explanation of the safety symbols on the
product
Icon Description
To avoid overheating, do not cover the product.
Indication for a hot surface. Contact may cause
burns. Do not touch.
Bathroom zones (image B)
Never use the product while taking a shower or bath. This might
4
cause an electric shock.
Bathroom
0
The area inside the
bath.
1 The area is the same
width as zone 0 (the
width of the bath)
extending to 2.25 m
above the finished
floor level.
2 The area is the same
height as zone 1 (2.25
m), extended to 0.6 m
around the bath.
3 Remaining space
Installing the product (image C)
Only install the product in zone 3, at least 1.8 m above the
4
ground .
1. Drill holes with a diameter of 8 mm and place the plugs A
2. Insert the screws A , let them protrude 6 mm from the wall.
w
3. Attach the bathroom heater A
4. Make sure the product hangs secure.
Inserting the batteries (image D)
1. Open the battery compartment A
2. Place the battery.
3. Close A .
g
Setting the time
Time is only adjustable by remote control.
4
1. Press the set button A to display the hour.
y
2. Press the OK button A
u to set the current hour.
3. Press A
y to display the minute.
4. Press A u to set the current minute.
5. Press A to display the day of the week.
y
6. Press A
u to set the current day.
D1
Monday
D2 Tuesday
D3
Wednesday
D4 Thursday
D5
Friday
D6 Saturday
D7
Sunday
7. Press A
u to confirm the setting.
Shower room Minimum IP
rating
The area inside the IP67
shower basin.
The area is 2.25 m IP65
from the finished
floor level or the
height of the fixed
shower head.
The area is the same IP44
height as zone 1,
extended to 0.6 m
around the shower
basin.
Remaining space IP21
9 to the wall.
g .
Switching on the product
1. Plug the power cable A
2. Press the power button A
The product is now in standby mode.
4
When you switch on the product it makes a beep and the
4
display shows a "5" (Standby).
When the product is switched on (after a long period of time),
4
the product may emit some smell and fumes.
3. Press the on/off button A
You can control all the functions of the product with the remote
4
control and a selection of the functions with the buttons on
the display.
The display switches on.
4
Switching between modes
1. Repeatedly press mode button A
-
Fan
-
Half power
-
Full power
-
Standby
If both the half power indicator A
4
indicator A
mode.
2. Press A
t
The fan stops after 30 seconds in standby.
4
The default temperature is 23ºC when the temperature LED
4
A 5 is switched off.
Setting the temperature
Temperature setting is only adjustable by remote control.
4
The display shows the current room temperature when the
4
product is in standby mode.
The default temperature setting is 23°C.
4
1. Press the temperature up and down buttons A
set room temperature.
2. Press A
8
After setting the temperature, the heater automatically selects
4
e C. the required power depending on the temperature difference;
less than 2°C difference is half power, more than 2°C difference
is full power.
The product switches off when the room temperature is higher
4
than the set temperature.
4 The product switches on when the room temperature falls 2ºC
below the set temperature.
Setting the weekly program
Setting the weekly program is only possible by remote control.
4
1. Press the weekly program button A
program setting.
2. Press the day button A
3. Press the Edit button A
4. Press the timer on button A
hours).
5. Press timer off button A
hours).
The stopping time cannot be earlier than the starting time.
4
6. Press A
i
7. Press A
u
There are up to 6 programs available each day of the week.
4
8. Repeat step 2 to 7 to set another program.
9. Press A
o
The product switches to standby when the program has the
4
same starting and stopping time.
The weekly program is erased when A
4
6
into a power outlet.
r
q to switch on the product.
t to switch between standby and on.
8 to switch between:
3 and the full power
2 are switched on, the product is in full power
again to switch off the product.
to cancel.
o to enter into weekly
to set the starting day.
p
d to select a program.
f to set the starting time (only in
to set the stopping time (only in
s
to set the temperature.
to confirm the setting.
to activate the weekly program.
q
i to adjust the
is switched off.