Operating Precautions - Campingaz BF 5000 Gebrauchsanleitung

D - 2 - Tightness:
In case of leak, appliance gas supply must be shut
down using gas bottle cock and/or pressure reducing
valve handle.
Do not carry out leak tests with a flame, use a gas leak
detecting liquid.
- apply gas leak detecting liquid to bottle/pressure
reducing valve/hose/appliance unions.
- open the gas inlet (bottle cock and/or pressure reducing
valve handle).
- If bubbles appear, this means that there are gas leaks.
- to remove the leak, tighten hose nuts and/or hose
clamps if any. If a part is defective, have it replaced.
the appliance should not be returned to service until the
leak is removed.
- Close gas bottle cock.
Important: In case of gas leak or odour, immediately
close bottle cock and/or pressure reducing valve
handle. Enhance room ventilation by opening the
windows. Ask a specialised technician to check the
appliance and proper bottle connection.
a leak test should be carried out at least once a year and
whenever the gas bottle is changed.
E - uTILISATIoN

oPERATING PRECAuTIoNS:

Do NoT install the appliance next to a wall, curtains
or a sofa or armchair.
Do NoT cover the appliance with clothes or other
objects.
Do NoT move the appliance when in operation.
The appliance must ALWAYS be directed to the
centre of the room.
The appliance must be put in a dry place.
This appliance protecting grid is designed to
prevent fire hazards or burns and no part shall be
permanently removed.
ThE GRID DoES NoT ToTALLY PRoTECT YouNG
ChILDREN oR ThE DISABLED.
After use, close the cylinder tap and/or the gas
cylinder knob.
E - 1 - IGNITING ThE APPLIANCE:
Note: Gas opening and closing controls are located on
gas bottle and/or on pressure reducing valve.
The ignition spark, gas inlet control and power control are
operated on the control panel located in the top right-hand
corner of the appliance. (fig. 1 item 1) and (fig. 5 items A,
B)
1- open bottle cock and/or pressure reducing valve
handle and carry out a leak test.
2-Set handle (a) to position (START) and press the
handle for 10 seconds to allow the gas to reach the
pilot burner(fig. 5).
3- Fully press several times the LH button marked with a
stylised lightning ( ) (B) for lighting up the flame, while
holding handle (a) or control button (a) depressed for
10 seconds. the thermocouple is activated and the
safety valve does not cut off gas feed.
release button a or handle a.
4- Check whether the appliance did light up. If not, repeat
the procedure from step 2.
Note: Some air may be trapped in the gas line. This will
prevent the appliance from lighting up during the first
attempt. In this case, it is necessary to repeat the ignition
procedure several times until the safety pilot burner lights
up. During appliance operation, the safety pilot burner
must remain permanently lit in order to ensure correct
operation of the atmosphere analyser.
During the first setting to service, operate the appliance at
maximum power for at least 15 minutes in order to eliminate
the typical new appliance smell due to the presence of
protecting substances applied to the component parts.
Ventilate the room during this operation.
E - 2 - Setting temperature or power (FIG. 5):
Your appliance is equipped with a control knob which
allows to adjust the heating power.
- Set the heating temperature by positioning handle
index between positions (III) and (I) (3: see fig. 5 item
a
)
E - 3 - ShuTTING DoWN ThE APPLIANCE:
- Close bottle cock and/or gas pressure reducing valve
handle.
tHIS aPPLIaNCe IS eQUIPPeD WItH aN atMoSPHere
aNaLYSer DeVICe WHICH aUtoMatICaLLY tUrNS
oFF tHe aPPLIaNCe SHoULD tHe rooM CoNtaIN
too HIGH a CarBoN DIoxIDe PerCeNtaGe (Co
IN tHIS CaSe, tHoroUGHLY VeNtILate tHe rooM,
otHerWISe tHe aPPLIaNCe WILL Not reLIGHt.
F - REMoVING oR REPLACING ThE GAS BoTTLE
- Check that gas bottle cock and/or pressure reducing
valve handle is in the closed position.
- open appliance rear plate (fig. 4 item B) and remove the
bottle from its housing, taking care not to pull or bend the
hose.
- Disconnect pressure reducing valve from gas bottle.
- Install the new gas bottle and carry out a leak test as
described under paragraphs D-1 and D-2.
G - SToRAGE - SERVICING
1) Appliance
When it is not used, the appliance should remain open
and be stored in a dust-free place.
- remove stains with soapy water, when the appliance is
cold. Wipe off with a cloth.
- Do not use abrasives which might damage the paintwork.
- For heavy repairs, please call your vendor.
- the appliance must be periodically checked, at least
once a year, more particularly concerning condition of
the connecting hose.
2) hose between the pressure reducing valve and the
appliance
- Periodically check hose for condition and replace it if it
displays ageing signs or cracks.
- the hose must be replaced by a new one of same length
and equivalent quality.
- the hose must be replaced in compliance with the
above-mentioned periodicity for the respective countries.
- Comply with installation indications provided with these
new assemblies to be 0.50 m long, and with the
procedure described under paragraph C - 2.
- If your appliance is to remain unused for a long period,
disconnect gas bottle.
21
FR
).
2